HP SW TL881 DLT Mini-Lib/1 Compaq TL881 MiniLibrary System Users Guide (May 19 - Page 178

Removing and Replacing the Skin Cover Desktop, Models Only, Removing, Replacing

Get HP SW TL881 DLT Mini-Lib/1 PDF manuals and user guides View all HP SW TL881 DLT Mini-Lib/1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 178 highlights

Adding a Second Tape Drive D-3 Removing and Replacing the Skin Cover (Desktop Models Only) The skin cover is held in place by two screws on each side of the base module (Figure D-2). Figure D-2. Removing the Skin Cover SHR-1433 Removing Remove the skin cover from the base module as follows: 1. Remove the two screws on each side of the base module. 2. Grasp the cover by the sides at the bottom edge and pull outwards while lifting the cover straight up and off the chassis. Replacing To replace the skin cover on the base module: 1. Position the skin cover over the base module with the two tabs the two angled surfaces facing toward the front. 2. Slide the skin cover over the module until it touches the front panel. 3. Insert the two screws on each side through the skin cover into the base module, but don't tighten the screws until you have all four started.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Adding a Second Tape Drive
D-3
Removing and Replacing the Skin Cover (Desktop
Models Only)
The skin cover is held in place by two screws on each side of the base module
(Figure D-2).
SHR-1433
Figure D-2.
Removing the Skin Cover
Removing
Remove the skin cover from the base module as follows:
1.
Remove the two screws on each side of the base module.
2.
Grasp the cover by the sides at the bottom edge and pull outwards while
lifting the cover straight up and off the chassis.
Replacing
To replace the skin cover on the base module:
1.
Position the skin cover over the base module with the two tabs the two
angled surfaces facing toward the front.
2.
Slide the skin cover over the module until it touches the front panel.
3.
Insert the two screws on each side through the skin cover into the base
module, but don’t tighten the screws until you have all four started.