HP Surestore Tape Library Model 20/700 HP Surestore Tape Library Model 20/700 - Page 140

Loading a Cartridge into a 9840 Drive, Locating a Cartridge in the Storage Cells,

Get HP Surestore Tape Library Model 20/700 PDF manuals and user guides View all HP Surestore Tape Library Model 20/700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

Chapter 4 Loading a Cartridge into a 9840 Drive To load a cartridge in a 9840 drive: 1. Ensure that the drive is not in use. 2. Open the tape library right front door by pulling on the left side of the door. 3. Open the library left front door by using a latch key to unlock both locks. See Figure 32 on page 123. Turn the key counter clockwise to unlock them, then pull open the door. 4. Locate the cartridge (see Locating a Cartridge in the Storage Cells on page 127). 5. Insert the cartridge into the 9840 drive using the direction shown in Figure 40 on page 140. 6. Wait for one of the following messages to display on the drive's front panel and take the appropriate action, if necessary: - The Ready F (File Protected) message displays when a write-protected cartridge loads successfully. - The Ready U (File Unprotected) message displays when a cartridge that is not write-protected loads successfully. - The Ready A (VolSafe-enabled) message displays when a writeenabled VolSafe cartridge loads successfully. - The NTReady message displays when the tape in the cartridge has lost tension. Follow the instructions outlined in the 9840 Tape Drive User's Reference Manual to correct this condition. - The LOADxxxx message displays when the cartridge unsuccessfully loads, where the xxxx is a fault symptom code. Follow the instructions outlined in the 9840 Tape Drive User's Reference Manual to correct this condition. Chapter 4 Manual Operation 139

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
Chapter 4
Manual Operation
139
Chapter 4
Loading a Cartridge into a 9840 Drive
To load a cartridge in a 9840 drive:
1.
Ensure that the drive is not in use.
2.
Open the tape library right front door by pulling on the left side of the
door.
3.
Open the library left front door by using a latch key to unlock both locks.
See
Figure 32
on page 123. Turn the key counter clockwise to unlock
them, then pull open the door.
4.
Locate the cartridge (see
Locating a Cartridge in the Storage Cells
on
page 127).
5.
Insert the cartridge into the 9840 drive using the direction shown in
Figure
40
on page 140.
6.
Wait for one of the following messages to display on the drive’s front
panel and take the appropriate action, if necessary:
—
The
Ready F
(File Protected) message displays when a write-protected
cartridge loads successfully.
—
The
Ready U
(File Unprotected) message displays when a cartridge
that is not write-protected loads successfully.
—
The
Ready A
(VolSafe-enabled) message displays when a write-
enabled VolSafe cartridge loads successfully.
—
The
NTReady
message displays when the tape in the cartridge has
lost tension. Follow the instructions outlined in the
9840 Tape Drive
User’s Reference Manual
to correct this condition.
—
The
LOADxxxx
message displays when the cartridge unsuccessfully
loads, where the
xxxx
is a fault symptom code. Follow the instructions
outlined in the
9840 Tape Drive User’s Reference Manual
to correct
this condition.