HP rp8420 HP 9000 rp8420 Server - User Service Guide, Fifth Edition - Page 132

Example To downgrade the System Firmware image A firmware

Get HP rp8420 PDF manuals and user guides View all HP rp8420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

CAUTION: DO NOT RESET or AC POWER CYCLE the server unless you have received confirmation that DFW has completed successfully. Repeat the dfw command immediately if the firmware failed to complete successfully. NOTE (1): After a dfw copy of a Cell PDHC firmware image is captured, the version displayed by the sysrev command will not be correct until the cell PDHC is reset using the ru command or AC power is cycled. 4. Example (To downgrade the PDHC image B firmware) MP:CM> dfw ***** ***** ***** Duplicate Firmware Utility ***** ***** ***** ***** (C) Copyright 2001 Hewlett-Packard Company ***** ***** All Rights Reserved ***** ***** ***** ***** THIS PROGRAM IS NOT LICENSED TO CUSTOMERS ***** ***** ***** ***** This program is intended for use by trained HP support ***** ***** personnel only. HP shall not be liable for any damages ***** ***** resulting from unauthorized use of this program. This ***** ***** program is the property of HP. ***** ***** ***** ***** Version 1.04 ***** ***** ***** Flash Current Number Cabinet Name Partition Handle Firmware Version Comments 1 0 PDHC 0A 0 256 A.003.034 Current 2 0 PDHC 0B 0 264 A.003.034 Old 3 0 SFW 0A 0 320 22.002 Pri PA 4 0 SFW 0B 0 328 22.002 Sec PA 5 0 PDHC 1A 0 257 A.003.023 Current 6 0 PDHC 1B 0 265 A.003.023 Old 7 0 SFW 1A 0 321 21.001 Pri PA 8 0 SFW 1B 0 329 21.001 Sec PA Note: You can only duplicate one firmware type at a time. Enter the Entities to be updated (EX: 7,8) : 2 Enter the source entity for the PDHC firmware image: 5 Are you sure that you want to continue(Y/N): y **** Updating device PDHC 0B **** Erasing Flash(es). This may take several minutes. DFW has completed successfully for all entities Once DFW has completed, verify the following message is returned: DFW has completed successfully for all entities CAUTION: DO NOT RESET or AC POWER CYCLE the server unless you have received confirmation that DFW has completed successfully. Repeat the dfw command immediately if the firmware failed to complete successfully. NOTE (1): After a dfw copy of a Cell PDHC firmware image is captured, the version displayed by the sysrev command will not be correct until the cell PDHC is reset using the ru command or AC power is cycled. 5. Perform steps 6 and 7 from Step 6. 6. Example (To downgrade the System Firmware image A firmware) 132 Removal and Replacement

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
CAUTION:
DO NOT RESET
or
AC POWER CYCLE
the server unless you have received
confirmation that DFW has completed successfully. Repeat the
dfw
command immediately
if the firmware failed to complete successfully.
NOTE (1): After a
dfw
copy of a Cell PDHC firmware image is captured, the version displayed
by the
sysrev
command will not be correct until the cell PDHC is reset using the
ru
command or AC power is cycled.
4.
Example (To downgrade the PDHC image B firmware)
MP:CM> dfw
*********************************************************************
*****
*****
*****
Duplicate Firmware Utility
*****
*****
*****
*****
(C) Copyright 2001 Hewlett-Packard Company
*****
*****
All Rights Reserved
*****
*****
*****
*****
THIS PROGRAM IS NOT LICENSED TO CUSTOMERS
*****
*****
*****
*****
This program is intended for use by trained HP support
*****
*****
personnel only.
HP shall not be liable for any damages
*****
*****
resulting from unauthorized use of this program.
This
*****
*****
program is the property of HP.
*****
*****
*****
*****
Version
1.04
*****
*****
*****
*********************************************************************
Flash
Current
Number
Cabinet
Name
Partition
Handle
Firmware Version
Comments
------ --------- -------- --------- -------- ------------------ --------
1
0
PDHC 0A
0
256
A.003.034
Current
2
0
PDHC 0B
0
264
A.003.034
Old
3
0
SFW 0A
0
320
22.002
Pri PA
4
0
SFW 0B
0
328
22.002
Sec PA
5
0
PDHC 1A
0
257
A.003.023
Current
6
0
PDHC 1B
0
265
A.003.023
Old
7
0
SFW 1A
0
321
21.001
Pri PA
8
0
SFW 1B
0
329
21.001
Sec PA
Note: You can only duplicate one firmware type at a time.
Enter the Entities to be updated (EX: 7,8) : 2
Enter the source entity for the PDHC firmware image: 5
Are you sure that you want to continue(Y/N): y
**** Updating device PDHC 0B ****
Erasing Flash(es). This may take several minutes.
DFW has completed successfully for all entities
Once DFW has completed, verify the following message is returned:
DFW has completed successfully for all entities
CAUTION:
DO NOT RESET
or
AC POWER CYCLE
the server unless you have received
confirmation that DFW has completed successfully. Repeat the
dfw
command immediately
if the firmware failed to complete successfully.
NOTE (1): After a
dfw
copy of a Cell PDHC firmware image is captured, the version displayed
by the
sysrev
command will not be correct until the cell PDHC is reset using the
ru
command or AC power is cycled.
5.
Perform steps 6 and 7 from
Step 6
.
6.
Example (To downgrade the System Firmware image A firmware)
132
Removal and Replacement