HP rp8420 HP 9000 rp8420 Server - User Service Guide, Fifth Edition - Page 162

Replacing the PCI-X Card Cage Assembly, PCI-X Card Cage Assembly Detail

Get HP rp8420 PDF manuals and user guides View all HP rp8420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 162 highlights

Figure 6-54 PCI-X Card Cage Assembly Detail Replacing the PCI-X Card Cage Assembly 1. Tilt the assembly toward the chassis. Position the assembly at an angle so that the retaining standoff pins engage. 2. Using extractors, slide board toward system backplane until fully seated. 3. Reconnect the two cable bundles at the rear of the mass storage board and tighten the two captive screws onboard the backplane near the extractor levers. 4. Replace all PCI cards into their proper slots. 5. Reconnect all PCI card cables. 6. Reconnect the PCI OLR ribbon cable to the PCI backplane. 7. Re-engage the PCI power supplies. 8. Remove the air baffle from the old PCI-X card cage assembly and install on the new PCI-X assembly. See Figure 6-55 for the location of the air baffle. The air baffle attaches to the PCI-X assembly by two captive thumbscrews. One thumbscrew is located on each end of the air baffle. 162 Removal and Replacement

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
Figure 6-54 PCI-X Card Cage Assembly Detail
Replacing the PCI-X Card Cage Assembly
1.
Tilt the assembly toward the chassis. Position the assembly at an angle so that the retaining
standoff pins engage.
2.
Using extractors, slide board toward system backplane until fully seated.
3.
Reconnect the two cable bundles at the rear of the mass storage board and tighten the two
captive screws onboard the backplane near the extractor levers.
4.
Replace all PCI cards into their proper slots.
5.
Reconnect all PCI card cables.
6.
Reconnect the PCI OLR ribbon cable to the PCI backplane.
7.
Re-engage the PCI power supplies.
8.
Remove the air baffle from the old PCI-X card cage assembly and install on the new PCI-X
assembly. See
Figure 6-55
for the location of the air baffle.
The air baffle attaches to the PCI-X assembly by two captive thumbscrews. One thumbscrew
is located on each end of the air baffle.
162
Removal and Replacement