IBM 4851 514 Service Guide - Page 29

sufficient

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Updated October, 2008 Installing the IBM SurePOS 500 Model 514 Figure 11. Cable routing label 1. Connect the cables as shown in as shown in "Rear view and connectors" on page 5. Signal cables must be routed to the right of the AC power cable, as shown in Figure 11. 2. Secure the cables to the cable-tie bar with tie-warps if desired. Cut the end of the tie-wraps flush so that no jagged edges are exposed. Attention: The rear cover will not close properly if signal cables are routed to the left of the AC power cable. See Figure 11 for routing. 3. For cables routed under the counter, install a cable tie around all rear connector panel cables exiting through the hole. Allow sufficient length for cleaning and servicing. Chapter 2. Installing the IBM SurePOS 500 Model 514 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
1.
Connect
the
cables
as
shown
in
as
shown
in
“Rear
view
and
connectors”
on
page
5.
Signal
cables
must
be
routed
to
the
right
of
the
AC
power
cable,
as
shown
in
Figure
11.
2.
Secure
the
cables
to
the
cable-tie
bar
with
tie-warps
if
desired.
Cut
the
end
of
the
tie-wraps
flush
so
that
no
jagged
edges
are
exposed.
Attention:
The
rear
cover
will
not
close
properly
if
signal
cables
are
routed
to
the
left
of
the
AC
power
cable.
See
Figure
11
for
routing.
3.
For
cables
routed
under
the
counter,
install
a
cable
tie
around
all
rear
connector
panel
cables
exiting
through
the
hole.
Allow
sufficient
length
for
cleaning
and
servicing.
Figure
11.
Cable
routing
label
Installing
the
IBM
SurePOS
500
Model
514
Updated
October,
2008
Chapter
2.
Installing
the
IBM
SurePOS
500
Model
514
13