IBM 4851 514 Service Guide - Page 47

distributed

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Updated October, 2008 Mounting the SurePOS 500 Model 514 8. If you are installing a distributed-character display or an all points addressable (APA) display, see "Mounting a distributed customer display and APA display to a cash drawer" on page 42. 9. Connect the peripheral cables to the appropriate ports on the rear connector panel. See "Routing and connecting cables to the rear connector panel" on page 12. Note: If you are installing a distributed-character display, route the cable through the unattached rear modesty panel C in Figure 24 on page 32. 10. Use tie-wraps to secure cables to the cable-tie bar. Be sure to run cables to the right of the power cable when viewed from the rear. 11. Replace the rear cover. 12. Install the filler panels after you route all the cables to your system. Note that filler panel A locks filler panels B onto the tray. Install the filler panels after you have routed all of the cables. a. Install the outer ends of the filler panels B into the integration tray. Notice that the printer filler panel, shown on the right, is narrower than the system filler panel. Also, the system filler panel has a bottom slot that allows you to route the cables out the back. b. Use the narrow filler panel A to lock the filler panels together between the system and the printer. Note: Depending upon your desired configuration, you could have unused filler panels. 13. Tilt the modesty cover C so the front hooks attach to the tray; then push down until the cover snaps into place. Chapter 3. Mounting the SurePOS 500 Model 514 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
8.
If
you
are
installing
a
distributed-character
display
or
an
all
points
addressable
(APA)
display,
see
“Mounting
a
distributed
customer
display
and
APA
display
to
a
cash
drawer”
on
page
42.
9.
Connect
the
peripheral
cables
to
the
appropriate
ports
on
the
rear
connector
panel.
See
“Routing
and
connecting
cables
to
the
rear
connector
panel”
on
page
12.
Note:
If
you
are
installing
a
distributed-character
display,
route
the
cable
through
the
unattached
rear
modesty
panel
±C²
in
Figure
24
on
page
32.
10.
Use
tie-wraps
to
secure
cables
to
the
cable-tie
bar.
Be
sure
to
run
cables
to
the
right
of
the
power
cable
when
viewed
from
the
rear.
11.
Replace
the
rear
cover.
12.
Install
the
filler
panels
after
you
route
all
the
cables
to
your
system.
Note
that
filler
panel
±A²
locks
filler
panels
±B²
onto
the
tray.
Install
the
filler
panels
after
you
have
routed
all
of
the
cables.
a.
Install
the
outer
ends
of
the
filler
panels
±B²
into
the
integration
tray.
Notice
that
the
printer
filler
panel,
shown
on
the
right,
is
narrower
than
the
system
filler
panel.
Also,
the
system
filler
panel
has
a
bottom
slot
that
allows
you
to
route
the
cables
out
the
back.
b.
Use
the
narrow
filler
panel
±A²
to
lock
the
filler
panels
together
between
the
system
and
the
printer.
Note:
Depending
upon
your
desired
configuration,
you
could
have
unused
filler
panels.
13.
Tilt
the
modesty
cover
±C²
so
the
front
hooks
attach
to
the
tray;
then
push
down
until
the
cover
snaps
into
place.
Mounting
the
SurePOS
500
Model
514
Updated
October,
2008
Chapter
3.
Mounting
the
SurePOS
500
Model
514
31