IBM 4851 514 Service Guide - Page 38

mount, system, directly, countertop

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Mounting the SurePOS 500 Model 514 Updated October, 2008 To mount the system directly on a countertop: Note: Before you begin, acquire two mounting screws. These are not supplied. 1. Remove the rear cover. 2. Remove the cable-tie bar by loosening the thumbscrew. 3. Optionally, remove the power supply for easy access to the screws. See "Power supply - removing and replacing" on page 68. 4. Use the SurePOS 500 Model 514 base plate as a pattern for drilling two mounting-screw holes at location A in Figure 14. If you plan to route the cables underneath the counter, use the base plate as a pattern to drill the cable opening and for drilling the holes for the mounting screws. 5. Attach the system to the countertop with two mounting screws. A Figure 14. Attaching the base foot to the countertop 6. Swing out the cable-tie bar by loosening the thumbscrew. 7. Connect the power cable to the power supply. 8. Connect the peripheral device cables to the appropriate ports on the rear connector panel. Make the connections on the bottom row of the connector panel first and work upward. Ensure that the cables are routed to the right of the power cord. Note: For a diagram of the port layout, see "Routing and connecting cables to the rear connector panel" on page 12. 9. Rotate the cable-tie bar back into place and tighten the thumbscrew. 10. Use tie-wraps to secure cables to the cable-tie bar, if desired. 11. Replace the rear cover. 12. Plug the AC power cord into an AC outlet. 13. After your installation is complete, switch ON the power to the SurePOS 500 Model 514 and verify that the system is operating correctly by checking the indicator lights (LEDs) on the front of the touch screen. See "Powering on and the LED states" on page 14. 14. Install your software. Refer to IBM SurePOS Model 514 Operating System Installation Guide. 22 SurePOS 500 Model 514

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
To
mount
the
system
directly
on
a
countertop
:
Note:
Before
you
begin,
acquire
two
mounting
screws.
These
are
not
supplied.
1.
Remove
the
rear
cover.
2.
Remove
the
cable-tie
bar
by
loosening
the
thumbscrew.
3.
Optionally,
remove
the
power
supply
for
easy
access
to
the
screws.
See
“Power
supply
–
removing
and
replacing”
on
page
68.
4.
Use
the
SurePOS
500
Model
514
base
plate
as
a
pattern
for
drilling
two
mounting-screw
holes
at
location
±A²
in
Figure
14.
If
you
plan
to
route
the
cables
underneath
the
counter,
use
the
base
plate
as
a
pattern
to
drill
the
cable
opening
and
for
drilling
the
holes
for
the
mounting
screws.
5.
Attach
the
system
to
the
countertop
with
two
mounting
screws.
6.
Swing
out
the
cable-tie
bar
by
loosening
the
thumbscrew.
7.
Connect
the
power
cable
to
the
power
supply.
8.
Connect
the
peripheral
device
cables
to
the
appropriate
ports
on
the
rear
connector
panel.
Make
the
connections
on
the
bottom
row
of
the
connector
panel
first
and
work
upward.
Ensure
that
the
cables
are
routed
to
the
right
of
the
power
cord.
Note:
For
a
diagram
of
the
port
layout,
see
“Routing
and
connecting
cables
to
the
rear
connector
panel”
on
page
12.
9.
Rotate
the
cable-tie
bar
back
into
place
and
tighten
the
thumbscrew.
10.
Use
tie-wraps
to
secure
cables
to
the
cable-tie
bar,
if
desired.
11.
Replace
the
rear
cover.
12.
Plug
the
AC
power
cord
into
an
AC
outlet.
13.
After
your
installation
is
complete,
switch
ON
the
power
to
the
SurePOS
500
Model
514
and
verify
that
the
system
is
operating
correctly
by
checking
the
indicator
lights
(LEDs)
on
the
front
of
the
touch
screen.
See
“Powering
on
and
the
LED
states”
on
page
14.
14.
Install
your
software.
Refer
to
IBM
SurePOS
Model
514
Operating
System
Installation
Guide
.
A
Figure
14.
Attaching
the
base
foot
to
the
countertop
Mounting
the
SurePOS
500
Model
514
Updated
October,
2008
22
SurePOS
500
Model
514