IBM 4851 514 Service Guide - Page 58

Installing, additional, peripheral, devices, Mounting, distributed, customer, display, drawer

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Installing additional peripheral devices Updated October, 2008 Installing additional peripheral devices Attention: Before you use the following procedures to install additional peripheral devices, see Appendix D, "Safety information," on page 123. Mounting a distributed customer display and APA display to a cash drawer The SurePOS 500 Series provides a powered, 15-pin, serial port for attaching a distributed customer display, APA character-graphic display, or other device requiring a powered serial connection. The SurePOS 500 Series distributed customer display is mounted behind the cash-drawer modesty panel. It can also be mounted to a countertop with customer-provided hardware. Use these instructions to mount a character display to a cash drawer. 1. Prepare the system for installation of the distributed customer display. a. Switch OFF the power at the system unit. b. Remove the SurePOS 500 Series rear cover (see "Rear cover - removing and replacing" on page 61) to access the rear connector panel. 2. Prepare the distributed customer display to be installed on an integration tray. a. Route the distributed customer display cable through the mounting post (and post extension, if used) and plug the cable into the display, as shown in Figure 33. Figure 33. Attaching the distributed customer display cable b. Attach the character display top to its post by pressing the display down on the post until it snaps into place. 3. Go to the appropriate procedure for a non-keyboard integration tray or keyboard integration tray to complete the installation of the distributed customer display: v For installation of a distributed customer display on a non-keyboard integration tray, go to Step 4 on page 43. v For installation of a distributed customer display on a keyboard integration tray, go to Step 5 on page 44. 42 SurePOS 500 Model 514

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Installing
additional
peripheral
devices
Attention:
Before
you
use
the
following
procedures
to
install
additional
peripheral
devices,
see
Appendix
D,
“Safety
information,”
on
page
123.
Mounting
a
distributed
customer
display
and
APA
display
to
a
cash
drawer
The
SurePOS
500
Series
provides
a
powered,
15-pin,
serial
port
for
attaching
a
distributed
customer
display,
APA
character-graphic
display,
or
other
device
requiring
a
powered
serial
connection.
The
SurePOS
500
Series
distributed
customer
display
is
mounted
behind
the
cash-drawer
modesty
panel.
It
can
also
be
mounted
to
a
countertop
with
customer-provided
hardware.
Use
these
instructions
to
mount
a
character
display
to
a
cash
drawer.
1.
Prepare
the
system
for
installation
of
the
distributed
customer
display.
a.
Switch
OFF
the
power
at
the
system
unit.
b.
Remove
the
SurePOS
500
Series
rear
cover
(see
“Rear
cover
–
removing
and
replacing”
on
page
61)
to
access
the
rear
connector
panel.
2.
Prepare
the
distributed
customer
display
to
be
installed
on
an
integration
tray.
a.
Route
the
distributed
customer
display
cable
through
the
mounting
post
(and
post
extension,
if
used)
and
plug
the
cable
into
the
display,
as
shown
in
Figure
33.
b.
Attach
the
character
display
top
to
its
post
by
pressing
the
display
down
on
the
post
until
it
snaps
into
place.
3.
Go
to
the
appropriate
procedure
for
a
non-keyboard
integration
tray
or
keyboard
integration
tray
to
complete
the
installation
of
the
distributed
customer
display:
v
For
installation
of
a
distributed
customer
display
on
a
non-keyboard
integration
tray,
go
to
Step
4
on
page
43.
v
For
installation
of
a
distributed
customer
display
on
a
keyboard
integration
tray,
go
to
Step
5
on
page
44.
Figure
33.
Attaching
the
distributed
customer
display
cable
Installing
additional
peripheral
devices
Updated
October,
2008
42
SurePOS
500
Model
514