IBM 4851 514 Service Guide - Page 96

Removing, replacing, full-size, slide, assembly

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Removing and replacing FRUs Updated October, 2008 5. Remove the integration tray. 6. Open the cash drawer and pull it all the way out. 7. Remove the till. 8. Push in on the buttons in the rails, as shown in Figure 66, and pull up on the front of the drawer until the drawer is free from the slides. Pull the drawer forward out of the base. Rail Button (one on each side) Drawer Guide Figure 66. Removing and replacing a full size cash drawer To replace a cash drawer: 1. Make sure that the latch assembly is unlatched; otherwise, the drawer will not close properly. 2. Pull both slides all the way out. 3. Position the rear of the drawer into the slides so that the drawer guide on each side of the drawer aligns with the corresponding opening on each side, as shown in Figure 66. 4. Pivot the front of the drawer downward until it is positioned fully into the slides. 5. Close the drawer to make sure it closes correctly and remains closed. Removing and replacing a full-size slide assembly To remove a cash-drawer slide assembly: 1. Disconnect the cash drawer cable. 2. Remove the drawer as described at "Removing and replacing a full-size drawer" on page 79). 3. Remove the latch and sensor assembly (see "Removing and replacing the latch and sensor assembly" on page 83). 4. Remove the three screws that secure the slide to the base and lift out the slide assembly, as shown in Figure 67 on page 81. 5. If necessary, remove the top cover from the base (see "Removing and replacing the top cover" on page 81). 80 SurePOS 500 Model 514

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
5.
Remove
the
integration
tray.
6.
Open
the
cash
drawer
and
pull
it
all
the
way
out.
7.
Remove
the
till.
8.
Push
in
on
the
buttons
in
the
rails,
as
shown
in
Figure
66,
and
pull
up
on
the
front
of
the
drawer
until
the
drawer
is
free
from
the
slides.
Pull
the
drawer
forward
out
of
the
base.
To
replace
a
cash
drawer:
1.
Make
sure
that
the
latch
assembly
is
unlatched;
otherwise,
the
drawer
will
not
close
properly.
2.
Pull
both
slides
all
the
way
out.
3.
Position
the
rear
of
the
drawer
into
the
slides
so
that
the
drawer
guide
on
each
side
of
the
drawer
aligns
with
the
corresponding
opening
on
each
side,
as
shown
in
Figure
66.
4.
Pivot
the
front
of
the
drawer
downward
until
it
is
positioned
fully
into
the
slides.
5.
Close
the
drawer
to
make
sure
it
closes
correctly
and
remains
closed.
Removing
and
replacing
a
full-size
slide
assembly
To
remove
a
cash-drawer
slide
assembly:
1.
Disconnect
the
cash
drawer
cable.
2.
Remove
the
drawer
as
described
at
“Removing
and
replacing
a
full-size
drawer”
on
page
79).
3.
Remove
the
latch
and
sensor
assembly
(see
“Removing
and
replacing
the
latch
and
sensor
assembly”
on
page
83).
4.
Remove
the
three
screws
that
secure
the
slide
to
the
base
and
lift
out
the
slide
assembly,
as
shown
in
Figure
67
on
page
81.
5.
If
necessary,
remove
the
top
cover
from
the
base
(see
“Removing
and
replacing
the
top
cover”
on
page
81).
Rail
Button (one on each side)
Drawer Guide
Figure
66.
Removing
and
replacing
a
full
size
cash
drawer
Removing
and
replacing
FRUs
Updated
October,
2008
80
SurePOS
500
Model
514