IBM 4851 514 Service Guide - Page 59

Installing, additional, peripheral, devices

Get IBM 4851 514 PDF manuals and user guides View all IBM 4851 514 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Updated October, 2008 Installing additional peripheral devices 4. To install a distributed customer display D on a non-keyboard integration tray, perform the following steps: a. Remove the filler panels A and B (two) and the rear modesty panel C from the integration tray, as shown in Figure 34. Figure 34. Attaching the distributed customer display to the system unit b. Remove one of the two plugs E in the rear modesty panel. Figure 34 shows one plug removed. c. Route the character display cable through the hole in the modesty panel. You may need to lay the display on its side to connect the display cable to the rear connector panel. d. Route the character display cable to the rear connector panel. Plug it into the 15-pin serial connector, as shown in "Rear view and connectors" on page 5. e. Reinstall the rear cover of the SurePOS 500 Model 514 (see "Rear cover - removing and replacing" on page 61). f. Reinstall the filler panels B , and then install A , as shown in Figure 34. g. Attach the post, through the modesty cover C to the cash drawer with 2 thumbscrews F . Snap the entire unit into place at the rear of the tray. Chapter 3. Mounting the SurePOS 500 Model 514 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
4.
To
install
a
distributed
customer
display
±D²
on
a
non-keyboard
integration
tray,
perform
the
following
steps:
a.
Remove
the
filler
panels
±A²
and
±B²
(two)
and
the
rear
modesty
panel
±C²
from
the
integration
tray,
as
shown
in
Figure
34.
b.
Remove
one
of
the
two
plugs
±E²
in
the
rear
modesty
panel.
Figure
34
shows
one
plug
removed.
c.
Route
the
character
display
cable
through
the
hole
in
the
modesty
panel.
You
may
need
to
lay
the
display
on
its
side
to
connect
the
display
cable
to
the
rear
connector
panel.
d.
Route
the
character
display
cable
to
the
rear
connector
panel.
Plug
it
into
the
15-pin
serial
connector,
as
shown
in
“Rear
view
and
connectors”
on
page
5.
e.
Reinstall
the
rear
cover
of
the
SurePOS
500
Model
514
(see
“Rear
cover
–
removing
and
replacing”
on
page
61).
f.
Reinstall
the
filler
panels
±B²
,
and
then
install
±A²
,
as
shown
in
Figure
34.
g.
Attach
the
post,
through
the
modesty
cover
±C²
to
the
cash
drawer
with
2
thumbscrews
±F²
.
Snap
the
entire
unit
into
place
at
the
rear
of
the
tray.
Figure
34.
Attaching
the
distributed
customer
display
to
the
system
unit
Installing
additional
peripheral
devices
Updated
October,
2008
Chapter
3.
Mounting
the
SurePOS
500
Model
514
43