Lenovo ThinkServer RD210 Hardware Maintenance Manual - Page 103

of the controller and remove it from the package.

Get Lenovo ThinkServer RD210 PDF manuals and user guides View all Lenovo ThinkServer RD210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

1. Read the safety information in Chapter 2 "Safety information" on page 3 and "Installation guidelines" on page 67. 2. Turn off the server and peripheral devices and disconnect the power cords and all external cables, if necessary. Note: When you disconnect the power source from the server, you will lose the ability to view the LEDs because the LEDs will not be lit with the power source removed. Before disconnecting the power source, make a note of which LEDs are lit, including the LEDs that are lit on the operation information panel, the EasyLED panel, and LEDs that are lit inside the server on the system board; then, see the "EasyLED" on page 20 for information on how to solve the problem. 3. Remove the cover (see "Removing and replacing the cover" on page 72). 4. Touch the static-protective package that contains the new ServeRAID-MR10i SAS/SATA controller to any unpainted surface on the outside of the server; then, grasp the adapter by the top edge or upper corners of the controller and remove it from the package. 5. Align the ServeRAID-MR10i SAS/SATA controller so that the keys align correctly with the connector on the SAS/SATA RAID riser card assembly. 6. Insert the SAS/SATA adapter into the connector on the SAS/SATA RAID riser-card until it is firmly seated. Attention: Incomplete insertion might cause damage to the server or the adapter. 1 USB embedded connector 2 RAID adapter connector 3 Riser card error LED 4 SAS/SATA RAID riser card 000000 0 000000 0 000000 0 000000 000000 Chapter 7. Installing optional devices and replacing customer replaceable units 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
1.
Read the safety information in Chapter 2 “Safety information” on page 3 and “Installation guidelines”
on page 67.
2.
Turn off the server and peripheral devices and disconnect the power cords and all external cables, if
necessary.
Note:
When you disconnect the power source from the server, you will lose the ability to view the LEDs
because the LEDs will not be lit with the power source removed. Before disconnecting the power source,
make a note of which LEDs are lit, including the LEDs that are lit on the operation information panel, the
EasyLED panel, and LEDs that are lit inside the server on the system board; then, see the “EasyLED” on
page 20 for information on how to solve the problem.
3.
Remove the cover (see “Removing and replacing the cover” on page 72).
4.
Touch the static-protective package that contains the new ServeRAID-MR10i SAS/SATA controller to any
unpainted surface on the outside of the server; then, grasp the adapter by the top edge or upper corners
of the controller and remove it from the package.
5.
Align the ServeRAID-MR10i SAS/SATA controller so that the keys align correctly with the connector on
the SAS/SATA RAID riser card assembly.
6.
Insert the SAS/SATA adapter into the connector on the SAS/SATA RAID riser-card until it is firmly seated.
Attention:
Incomplete insertion might cause damage to the server or the adapter.
1
USB embedded connector
2
RAID adapter connector
3
Riser card error LED
4
SAS/SATA RAID riser card
Chapter 7
.
Installing optional devices and replacing customer replaceable units
95