Lenovo ThinkServer RD210 Hardware Maintenance Manual - Page 116

Removing the hot-swap SAS/SATA hard disk drive backplane, Lift the backplane out of the server.

Get Lenovo ThinkServer RD210 PDF manuals and user guides View all Lenovo ThinkServer RD210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Removing the hot-swap SAS/SATA hard disk drive backplane To remove the hot-swap SAS/SATA hard disk drive backplane, complete the following steps: 1. Read the safety information in Chapter 2 "Safety information" on page 3 and "Installation guidelines" on page 67. 2. Turn off the server and peripheral devices and disconnect all power cords. 3. Remove the cover (see "Removing and replacing the cover" on page 72). 4. Pull the hard disk drives out of the server slightly to disengage them from the backplane. 5. Disconnect the power cable from the power backplane. 6. Disconnect the signal cable from the system board. 7. Lift up to remove the backplane from the slots. 8. Push backwards on the backplane until it is clear of the slots. 9. Lift the backplane out of the server. 10. Disconnect the power cable and the signal cable from the disk drive backplane. 1 Backplane tabs 2 Hard disk drive backplane 3 Backplane tabs 4 Backplane bracket slots 11. If you are instructed to return the backplane, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the hot-swap SAS/SATA hard disk drive backplane To install the replacement hot-swap SAS/SATA hard disk drive backplane, complete the following steps: 1. Read the safety information in Chapter 2 "Safety information" on page 3 and "Installation guidelines" on page 67. 2. Connect the power cable and signal cable to the replacement backplane. 108 ThinkServer RD210 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Removing the hot-swap SAS/SATA hard disk drive backplane
To remove the hot-swap SAS/SATA hard disk drive backplane, complete the following steps:
1.
Read the safety information in Chapter 2 “Safety information” on page 3 and “Installation guidelines”
on page 67.
2.
Turn off the server and peripheral devices and disconnect all power cords.
3.
Remove the cover (see “Removing and replacing the cover” on page 72).
4.
Pull the hard disk drives out of the server slightly to disengage them from the backplane.
5.
Disconnect the power cable from the power backplane.
6.
Disconnect the signal cable from the system board.
7.
Lift up to remove the backplane from the slots.
8.
Push backwards on the backplane until it is clear of the slots.
9.
Lift the backplane out of the server.
10.Disconnect the power cable and the signal cable from the disk drive backplane.
1
Backplane tabs
2
Hard disk drive backplane
3
Backplane tabs
4
Backplane bracket slots
11.If you are instructed to return the backplane, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.
Installing the hot-swap SAS/SATA hard disk drive backplane
To install the replacement hot-swap SAS/SATA hard disk drive backplane, complete the following steps:
1.
Read the safety information in Chapter 2 “Safety information” on page 3 and “Installation guidelines”
on page 67.
2.
Connect the power cable and signal cable to the replacement backplane.
108
ThinkServer RD210 Hardware Maintenance Manual