Lenovo ThinkServer RD210 Hardware Maintenance Manual - Page 135

Removing and installing the bezel, Removing the bezel

Get Lenovo ThinkServer RD210 PDF manuals and user guides View all Lenovo ThinkServer RD210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

1 Battery retention clip 2 Battery 3 Posts 4 Battery mounting slots 5 Rings 6 Microprocessor 2 air baffle 7 Posts • Take the battery retention clip and place it underneath the other tab while pressing release tab toward the front of the server; then, press it down until it snaps in place to hold the battery carrier firmly in place. 6. Install the cover (see "Removing and replacing the cover" on page 72). 7. Slide the server into the rack. 8. Reconnect the power cords and all external cables, and turn on the server and peripheral devices. Removing and installing the bezel To remove and install the bezel, complete the steps in this section. Removing the bezel To remove the bezel, complete the following steps: 1. Read the safety information in Chapter 2 "Safety information" on page 3 and "Installation guidelines" on page 67. 2. Turn off the server and peripheral devices and disconnect all power cords. 3. Remove the hard disk drives and filler panels from the hard disk drive bays (see "Removing and installing a hot-swap hard disk drive" on page 78). 4. Remove the screws 1 from the bezel 2 . Chapter 7. Installing optional devices and replacing customer replaceable units 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
1
Battery retention clip
2
Battery
3
Posts
4
Battery mounting slots
5
Rings
6
Microprocessor 2 air baffle
7
Posts
•
Take the battery retention clip and place it underneath the other tab while pressing release tab
toward the front of the server; then, press it down until it snaps in place to hold the battery carrier
firmly in place.
6.
Install the cover (see “Removing and replacing the cover” on page 72).
7.
Slide the server into the rack.
8.
Reconnect the power cords and all external cables, and turn on the server and peripheral devices.
Removing and installing the bezel
To remove and install the bezel, complete the steps in this section.
Removing the bezel
To remove the bezel, complete the following steps:
1.
Read the safety information in Chapter 2 “Safety information” on page 3 and “Installation guidelines”
on page 67.
2.
Turn off the server and peripheral devices and disconnect all power cords.
3.
Remove the hard disk drives and filler panels from the hard disk drive bays (see “Removing and installing
a hot-swap hard disk drive” on page 78).
4.
Remove the screws
1
from the bezel
2
.
Chapter 7
.
Installing optional devices and replacing customer replaceable units
127