Lenovo ThinkServer RD210 Hardware Maintenance Manual - Page 117

Removing and installing the operator information panel assembly

Get Lenovo ThinkServer RD210 PDF manuals and user guides View all Lenovo ThinkServer RD210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

3. Insert the backplane into the drive cage. 4. Align the tabs on the backplane with the slots on the left and right brackets. 5. Push down firmly until the backplane is fully seated and the locking tabs snaps into place. 6. Reconnect the power cable and the signal cable from the disk drive backplane. 1 Backplane tabs 2 Hard disk drive backplane 3 Backplane tabs 4 Backplane bracket slots 7. Install the cover (see "Removing and replacing the cover" on page 72). 8. Replace the hard disk drives. 9. Slide the server into the rack. 10. Reconnect the power cords and any cables that were removed. 11. Turn on the peripheral devices and the server. Removing and installing the operator information panel assembly To remove and install the operator information panel assembly, complete the steps in this section. Removing the operator information panel assembly To remove the operator information panel, complete the following steps. 1. Read the safety information in Chapter 2 "Safety information" on page 3 and "Installation guidelines" on page 67. 2. Turn off the server and peripheral devices and disconnect all power cords; then, remove the cover (see "Removing and replacing the cover" on page 72). 3. Disconnect the cable from the back of the operator information panel assembly 1 . 4. Push the blue release latch 2 to the left until it unlatches. Chapter 7. Installing optional devices and replacing customer replaceable units 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
3.
Insert the backplane into the drive cage.
4.
Align the tabs on the backplane with the slots on the left and right brackets.
5.
Push down firmly until the backplane is fully seated and the locking tabs snaps into place.
6.
Reconnect the power cable and the signal cable from the disk drive backplane.
1
Backplane tabs
2
Hard disk drive backplane
3
Backplane tabs
4
Backplane bracket slots
7.
Install the cover (see “Removing and replacing the cover” on page 72).
8.
Replace the hard disk drives.
9.
Slide the server into the rack.
10.Reconnect the power cords and any cables that were removed.
11.Turn on the peripheral devices and the server.
Removing and installing the operator information panel assembly
To remove and install the operator information panel assembly, complete the steps in this section.
Removing the operator information panel assembly
To remove the operator information panel, complete the following steps.
1.
Read the safety information in Chapter 2 “Safety information” on page 3 and “Installation guidelines”
on page 67.
2.
Turn off the server and peripheral devices and disconnect all power cords; then, remove the cover (see
“Removing and replacing the cover” on page 72).
3.
Disconnect the cable from the back of the operator information panel assembly
1
.
4.
Push the blue release latch
2
to the left until it unlatches.
Chapter 7
.
Installing optional devices and replacing customer replaceable units
109