Home » Sony Manuals » Voice Recorders » Sony DVWM2000 » Manual Viewer

Sony DVWM2000 Product Manual (Operation Manual 1st Edition (Revised 6)) - Page 130

Item number, Settings, In 525-line mode, To set the ID code, TC&UB, TCG REGEN MODE

View all Sony DVWM2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Chapter 12 Setup Menus 12-4 Items in the Extended Setup Menu Menu items in the range 600 to 650, relating to the time code generator Item number Item name Settings 601 VITC POSITION SEL-1 In 525-line mode Select a line to insert the VITC in. 12H ... 16H ... 20H: Select any line from 12 to 20. Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. In 625-line mode Select a line to insert the VITC in. 9H ... 19H ... 22H: Select any line from 9 to 22. Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. 602 VITC POSITION SEL-2 In 525-line mode Select a line to insert the VITC in. 12H ... 18H ... 20H: Select any line from 12 to 20. Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. In 625-line mode Select a line to insert the VITC in. 9H ... 21H ... 22H: Select any line from 9 to 22. Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. 603 ID CODE PRESET Select whether or not to set the ID code. OFF : Do not set the ID code. ON: Set the ID code. To set the ID code: Press the F5 (SET) button with this menu item displayed in the menu display, to enter the ID code setting mode. You can then set the user ID digit by digit using the T and t buttons for digit selection. When all required digits have been set correctly, press the F5 (SET) button again to save the ID code and exit from the ID code setting mode. 604 ID CODE SW Select whether or not to record the ID code set using item 603 in the user bits. OFF : Record the normal data in the user bits. ON: Record the ID code in the user bits. 605 TCG REGEN MODE Select the signals to be regenerated when the time code generator is in the regeneration mode (i.e., when the function menu item TCG (F2) is set to REGEN). TC&UB : Both the time code and user bit signals are regenerated. TC: Only the time code signal is regenerated. UB: Only the user bit signal is regenerated. (Continued) 12-16 Chapter 12 Setup Menus

Section	Page
Table of Contents	5
Chapter 1 Overview	9
1-1 Features	9
1-2 Example System Configuration	12
1-3 Using the CD-ROM Manual	13
1-3-1 CD-ROM System Requirements	13
1-3-2 Preparations	13
1-3-3 Reading the CD-ROM Manual	13
Chapter 2 Location and Function of Parts	15
2-1 Control Panels	15
2-1-1 Upper Control Panel	16
2-1-2 Lower Control Panel	17
2-1-3 Switch Panel	28
2-2 Connector Panel	29
Chapter 3 Preparations	33
3-1 Connections to External Devices	33
3-1-1 Connections to Digital Devices	33
3-1-2 Connections to Analog Devices	34
3-2 Reference Signals for Video Output and Servo System	35
3-2-1 External Sync Signal for the Internal Reference Video Signal Generator	35
3-2-2 Reference Signal for the Servo System	36
3-2-3 Connecting Reference Signals	37
3-3 Setup	39
3-4 Superimposed Character Information	40
3-5 Cassettes	42
3-5-1 Cassette Types	42
3-5-2 Inserting and Ejecting Cassettes	42
3-5-3 Preventing Accidental Erasure of Recordings	43
3-6 Using a Memory Stick	44
3-6-1 Notes on Memory Stick	44
Chapter 4 Recording and Playback	47
4-1 Recording	47
4-1-1 Preparations for Recording	47
4-1-2 Recording Time Code and User Bit Values	48
4-1-3 Recording Procedure	51
4-2 Playback	52
4-2-1 Preparations for Playback	52
4-2-2 Playback Procedures	53
4-2-3 Dynamic Motion Control (DMC) Playback	57
Chapter 5 Editing	61
5-1 Automatic Editing	61
5-1-1 Overview	61
5-1-2 Switch and Menu Settings	62
5-1-3 Selecting the Editing Mode	63
5-1-4 Setting Edit Points	63
5-1-5 Modifying and Deleting Edit Points	66
5-1-6 Cue-Up to Edit Points and Preroll	67
5-1-7 Preview	67
5-1-8 Carrying Out Automatic Editing	68
5-2 DMC Editing	71
5-2-1 Overview of DMC Editing	71
5-2-2 Carrying Out DMC Editing	72
5-3 Special Automatic Editing Methods	73
5-3-1 Quick Editing	73
5-3-2 Continuous Editing	73
5-3-3 Standalone Editing	74
5-3-4 Manual Editing	74
5-3-5 Preread Editing	74
Chapter 6 Shot Mark Function	77
6-1 Overview	77
6-2 Shot Mark Operation Menu	78
6-3 Shot Mark Operations	79
6-3-1 Reading Shot Marks	79
6-3-2 Writing Shot Marks	79
6-3-3 Shot Mark List Operations	80
6-3-4 Cueing Up to Shot Marks	82
6-3-5 Reading In Shot Data	83
6-3-6 Sorting Shot Marks	84
Chapter 7 Tele-File	85
7-1 Overview of Tele-File Functions	85
7-2 Opening the Tele-File Menu	86
7-3 Tele-File Menu	87
7-3-1 Clip Data Display	87
7-3-2 Preroll and Cue Up Using Clip Data	90
7-3-3 Modifying Clip Data	91
7-3-4 Undo/Resume Functions	94
7-3-5 Displaying and Modifying Attribute Data	95
Chapter 8 UMID Functions	97
8-1 Overview of UMID Functions	97
8-2 Recording UMIDs	98
8-3 UMID Output and Display	100
8-3-1 UMID Output Settings	100
8-3-2 UMID Display	100
Chapter 9 Essence Marks	103
9-1 Overview of Essence Mark Functions	103
9-2 Essence Mark Recording and Output	104
9-2-1 Essence Mark Recording	104
9-2-2 Essence Mark Output	104
Chapter 10 Auto Event Detector	105
10-1 Overview of Auto Event Detector Functions	105
10-2 Event Output and Recording	105
Chapter 11 Function Menu	107
11-1 Overview of the Function Menu	107
11-1-1 Function Menu Configuration	107
11-1-2 Using the Function Menu	108
11-2 Function Menu Item List	109
Chapter 12 Setup Menus	115
12-1 Setup Menu Configuration	115
12-2 Setup Menu Operations	116
12-3 Items in the Basic Setup Menu	119
12-4 Items in the Extended Setup Menu	122
Chapter 13 Setup Utility Menu Functions	145
13-1 Overview of Setup Utility Menu Functions	145
13-1-1 Using Memory Stick Data	145
Chapter 14 Maintenance and Inspection	149
14-1 Removing a Cassette When Tape Slack Occurs	149
14-2 Head Cleaning	149
14-3 Error Messages	150
14-4 Moisture Condensation	152
14-5 Regular Checks	153
14-5-1 Digital Hours Meter	153
14-5-2 Maintenance Timings	154
Appendix	155
Specifications	155

Match case Limit results 1 per page

12-4

Items in the Extended Setup Menu

Chapter 12

Setup Menus

12-16

Chapter 12

Setup Menus

Menu items in the range 600 to 650, relating to the time code generator

Item number

601

602

603

604

605

Item name

VITC POSITION SEL-1

VITC POSITION SEL-2

ID CODE PRESET

ID CODE SW

TCG REGEN MODE

Settings

In 525-line mode

Select a line to insert the VITC in.

12H ... 16H ... 20H:

Select any line from 12 to 20.

Note

You can insert the VITC signal in two places. To insert it in two places, set both

items 601 and 602.

In 625-line mode

Select a line to insert the VITC in.

9H ... 19H ... 22H:

Select any line from 9 to 22.

Note

You can insert the VITC signal in two places. To insert it in two places, set both

items 601 and 602.

In 525-line mode

Select a line to insert the VITC in.

12H ... 18H ... 20H:

Select any line from 12 to 20.

Note

You can insert the VITC signal in two places. To insert it in two places, set both

items 601 and 602.

In 625-line mode

Select a line to insert the VITC in.

9H ... 21H ... 22H:

Select any line from 9 to 22.

Note

You can insert the VITC signal in two places. To insert it in two places, set both

items 601 and 602.

Select whether or not to set the ID code.

OFF :

Do not set the ID code.

ON:

Set the ID code.

To set the ID code:

Press the F5 (SET) button with this menu item displayed in the menu display, to

enter the ID code setting mode. You can then set the user ID digit by digit using

the

and

buttons for digit selection. When all required digits have been set

correctly, press the F5 (SET) button again to save the ID code and exit from the

ID code setting mode.

Select whether or not to record the ID code set using item 603 in the user bits.

OFF :

Record the normal data in the user bits.

ON:

Record the ID code in the user bits.

Select the signals to be regenerated when the time code generator is in the

regeneration mode (i.e., when the function menu item TCG (F2) is set to

REGEN).

TC&UB :

Both the time code and user bit signals are regenerated.

TC:

Only the time code signal is regenerated.

UB:

Only the user bit signal is regenerated.

(Continued)