Sony DVWM2000 Product Manual (Operation Manual 1st Edition (Revised 6)) - Page 32

Time code input/output Audio monitor signal output TIME CODE OUT connector XLR 3-pin

Get Sony DVWM2000 PDF manuals and user guides View all Sony DVWM2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2-2 Connector Panel Chapter 2 Location and Function of Parts 2 CONTROL PANEL connector (round type, 10pin) In addition to the lower control panel, a similar control panel can be connected to this unit. To connect such a second control panel, use this connector. When two control panels are connected, use the PANEL SELECT switch on the switch panel (see page 2-14) to specify which control panel will control this unit. 3 VIDEO CONTROL connector (D-sub 15-pin) For remote control of the internal digital video processor, connect an optional BVR-50/50P Remote Control Unit. Always power off this unit before connecting the remote control unit. 4 OPTION connector (D-sub 9-pin) Not used. 5 REMOTE 1-IN(9P) connector (D-sub 9-pin) When using this unit together with another DVWM2000/M2000P/2000/2000P or an MPEG IMX, D-1, D-2, or Betacam VTR, and a BVE-series BVE-900/ 910/2000/9000/9000P/9100/9100P or other editor, connect the optional 9-pin remote control cable from the other unit to this connector. Depending on the setting of setup menu item 211, you can use this connector alone, or in a loop-through configuration with the REMOTE 1-OUT(9P) connector. 6 REMOTE 1-OUT(9P) connector (D-sub 9-pin) This provides the loop-through output for remote control signals from the REMOTE 1-IN(9P) connector. Depending on the setting of setup menu item 211, you can use this connector alone, or in a loop-through configuration with the REMOTE 1-IN(9P) connector. 7 RS-232C connector (D-sub 9-pin) Use this for monitoring and diagnosis of the state of this unit from an external computer, using ISR (Interactive Status Reporting). 2-18 Chapter 2 Location and Function of Parts 7 Time code input/output section TIME CODE IN OUT 1 TIME CODE IN connector 2 TIME CODE OUT connector 1 TIME CODE IN connector (XLR 3-pin, female) To record time code from an external device, input a time code signal from the time code output connector of the other device. 2 TIME CODE OUT connector (XLR 3-pin, male) This outputs a time code according to the operating state of the unit, as follows: • During playback: the playback time code By setting setup menu item 606, you can also output the time code from the internal time code generator locked to the playback time code. • During recording: the time code generated by the internal time code generator or the time code input to the TIME CODE IN connector. 8 Audio monitor signal output section MONITOR OUTPUT R L 1 MONITOR OUTPUT R connector 2 MONITOR OUTPUT L connector 1 MONITOR OUTPUT R connector (XLR 3-pin, male) This outputs the audio signals whose output destination was set to 'R' with the audio signal selection buttons in the audio control section. If multiple tracks have been set to 'R', the signals of those tracks are mixed for output. 2 MONITOR OUTPUT L connector (XLR 3-pin, male) This outputs the audio signals whose output destination was set to 'L' with the audio signal selection buttons in the audio control section. If multiple tracks have been set to 'L', the signals of those tracks are mixed for output.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
2-2
Connector Panel
Chapter 2
Location and Function of Parts
2-18
Chapter 2
Location and Function of Parts
2
CONTROL PANEL connector (round type, 10-
pin)
In addition to the lower control panel, a similar control
panel can be connected to this unit. To connect such a
second control panel, use this connector. When two
control panels are connected, use the PANEL SELECT
switch on the switch panel
(see page 2-14)
to specify
which control panel will control this unit.
3
VIDEO CONTROL connector (D-sub 15-pin)
For remote control of the internal digital video
processor, connect an optional BVR-50/50P Remote
Control Unit.
Always power off this unit before connecting the
remote control unit.
4
OPTION connector (D-sub 9-pin)
Not used.
5
REMOTE 1-IN(9P) connector (D-sub 9-pin)
When using this unit together with another DVW-
M2000/M2000P/2000/2000P or an MPEG IMX, D-1,
D-2, or Betacam VTR, and a BVE-series BVE-900/
910/2000/9000/9000P/9100/9100P or other editor,
connect the optional 9-pin remote control cable from
the other unit to this connector.
Depending on the setting of setup menu item 211, you
can use this connector alone, or in a loop-through
configuration with the REMOTE 1-OUT(9P)
connector.
6
REMOTE 1-OUT(9P) connector (D-sub 9-pin)
This provides the loop-through output for remote
control signals from the REMOTE 1-IN(9P)
connector.
Depending on the setting of setup menu item 211, you
can use this connector alone, or in a loop-through
configuration with the REMOTE 1-IN(9P) connector.
7
RS-232C connector (D-sub 9-pin)
Use this for monitoring and diagnosis of the state of
this unit from an external computer, using ISR
(Interactive Status Reporting).
7
Time code input/output section
1
TIME CODE IN connector (XLR 3-pin, female)
To record time code from an external device, input a
time code signal from the time code output connector
of the other device.
2
TIME CODE OUT connector (XLR 3-pin, male)
This outputs a time code according to the operating
state of the unit, as follows:
• During playback: the playback time code
By setting setup menu item 606, you can also output
the time code from the internal time code generator
locked to the playback time code.
• During recording: the time code generated by the
internal time code generator or the time code input to
the TIME CODE IN connector.
8
Audio monitor signal output section
1
MONITOR OUTPUT R connector (XLR 3-pin,
male)
This outputs the audio signals whose output
destination was set to ‘R’ with the audio signal
selection buttons in the audio control section. If
multiple tracks have been set to ‘R’, the signals of
those tracks are mixed for output.
2
MONITOR OUTPUT L connector (XLR 3-pin,
male)
This outputs the audio signals whose output
destination was set to ‘L’ with the audio signal
selection buttons in the audio control section. If
multiple tracks have been set to ‘L’, the signals of
those tracks are mixed for output.
TIME CODE
IN
OUT
1
TIME CODE IN connector
2
TIME CODE OUT connector
MONITOR OUTPUT
R
L
1
MONITOR OUTPUT R
connector
2
MONITOR OUTPUT L
connector