Sony DVWM2000 Product Manual (Operation Manual 1st Edition (Revised 6)) - Page 58

4-2

Playback

Chapter 4

Recording and Playback

4-12

Chapter 4

Recording and Playback

4

Holding down the DMC EDIT button, turn the

search dial, to set the initial speed at the playback

start point.

The speed you set appears in the speed indication

area. During this period the tape does not move.

When the initial speed setting is complete, release

the DMC EDIT button.

5

Press the PREVIEW button.

The tape is prerolled and played back at normal

speed from the on-air start point to the speed

variation start point. On passing the speed variation

start point, the MEMORY indicator begins to

flash, and playback begins at the speed set in step

4

.

6

Turn the search dial to vary the playback speed.

While the MEMORY indicator is flashing, the

speed variations are stored in memory. On passing

the speed variation end point, the MEMORY

indicator changes from flashing to continuously lit,

and the variable speed storing ends.

7

Press the STOP button to stop the tape.

If the MEMORY indicator lights continuously

before the speed variation end point

This indicates that the memory became full at that

point. It is therefore not possible to record more speed

variation. The maximum capacity is a duration of 120

seconds.

To amend the stored speed variation

Press the PREVIEW button.

The interval between the speed variation start and end

points is automatically played back at the stored speed.

Operate the search dial as required, to adjust the

playback speed.

Setting the initial speed to normal speed

In step

4

, press the PLAY button.

Executing DMC Playback

There are two methods of starting DMC playback.

• Starting playback at the on-air cue from the on-air

start point

• Starting playback immediately after preroll

Notes

• To avoid operating mistakes we recommend that you

use the VTR in standalone mode when carrying out

DMC playback.

• When using two VTRs connected for editing, you can

only use the recorder VTR for DMC playback, and

only when neither the RECORDER nor PLAYER

button is lit.

To start playback at the on-air cue from the

on-air start point

Use the following procedure.

1

Press the REVIEW button.

The REVIEW button lights, and the tape is cued up

to the on-air start point. After the tape is cued up,

the REVIEW button flashes.

2

At the moment the on-air cue is given, press the

REVIEW button once more.

The REVIEW button lights, and playback starts at

standard speed.

Between the speed variation start and end points,

DMC playback is carried out at the stored speed,

and then playback continues at normal speed and

the tape stops at the on-air end point.

Z

1,2

Section	Page
Table of Contents	5
Chapter 1 Overview	9
1-1 Features	9
1-2 Example System Configuration	12
1-3 Using the CD-ROM Manual	13
1-3-1 CD-ROM System Requirements	13
1-3-2 Preparations	13
1-3-3 Reading the CD-ROM Manual	13
Chapter 2 Location and Function of Parts	15
2-1 Control Panels	15
2-1-1 Upper Control Panel	16
2-1-2 Lower Control Panel	17
2-1-3 Switch Panel	28
2-2 Connector Panel	29
Chapter 3 Preparations	33
3-1 Connections to External Devices	33
3-1-1 Connections to Digital Devices	33
3-1-2 Connections to Analog Devices	34
3-2 Reference Signals for Video Output and Servo System	35
3-2-1 External Sync Signal for the Internal Reference Video Signal Generator	35
3-2-2 Reference Signal for the Servo System	36
3-2-3 Connecting Reference Signals	37
3-3 Setup	39
3-4 Superimposed Character Information	40
3-5 Cassettes	42
3-5-1 Cassette Types	42
3-5-2 Inserting and Ejecting Cassettes	42
3-5-3 Preventing Accidental Erasure of Recordings	43
3-6 Using a Memory Stick	44
3-6-1 Notes on Memory Stick	44
Chapter 4 Recording and Playback	47
4-1 Recording	47
4-1-1 Preparations for Recording	47
4-1-2 Recording Time Code and User Bit Values	48
4-1-3 Recording Procedure	51
4-2 Playback	52
4-2-1 Preparations for Playback	52
4-2-2 Playback Procedures	53
4-2-3 Dynamic Motion Control (DMC) Playback	57
Chapter 5 Editing	61
5-1 Automatic Editing	61
5-1-1 Overview	61
5-1-2 Switch and Menu Settings	62
5-1-3 Selecting the Editing Mode	63
5-1-4 Setting Edit Points	63
5-1-5 Modifying and Deleting Edit Points	66
5-1-6 Cue-Up to Edit Points and Preroll	67
5-1-7 Preview	67
5-1-8 Carrying Out Automatic Editing	68
5-2 DMC Editing	71
5-2-1 Overview of DMC Editing	71
5-2-2 Carrying Out DMC Editing	72
5-3 Special Automatic Editing Methods	73
5-3-1 Quick Editing	73
5-3-2 Continuous Editing	73
5-3-3 Standalone Editing	74
5-3-4 Manual Editing	74
5-3-5 Preread Editing	74
Chapter 6 Shot Mark Function	77
6-1 Overview	77
6-2 Shot Mark Operation Menu	78
6-3 Shot Mark Operations	79
6-3-1 Reading Shot Marks	79
6-3-2 Writing Shot Marks	79
6-3-3 Shot Mark List Operations	80
6-3-4 Cueing Up to Shot Marks	82
6-3-5 Reading In Shot Data	83
6-3-6 Sorting Shot Marks	84
Chapter 7 Tele-File	85
7-1 Overview of Tele-File Functions	85
7-2 Opening the Tele-File Menu	86
7-3 Tele-File Menu	87
7-3-1 Clip Data Display	87
7-3-2 Preroll and Cue Up Using Clip Data	90
7-3-3 Modifying Clip Data	91
7-3-4 Undo/Resume Functions	94
7-3-5 Displaying and Modifying Attribute Data	95
Chapter 8 UMID Functions	97
8-1 Overview of UMID Functions	97
8-2 Recording UMIDs	98
8-3 UMID Output and Display	100
8-3-1 UMID Output Settings	100
8-3-2 UMID Display	100
Chapter 9 Essence Marks	103
9-1 Overview of Essence Mark Functions	103
9-2 Essence Mark Recording and Output	104
9-2-1 Essence Mark Recording	104
9-2-2 Essence Mark Output	104
Chapter 10 Auto Event Detector	105
10-1 Overview of Auto Event Detector Functions	105
10-2 Event Output and Recording	105
Chapter 11 Function Menu	107
11-1 Overview of the Function Menu	107
11-1-1 Function Menu Configuration	107
11-1-2 Using the Function Menu	108
11-2 Function Menu Item List	109
Chapter 12 Setup Menus	115
12-1 Setup Menu Configuration	115
12-2 Setup Menu Operations	116
12-3 Items in the Basic Setup Menu	119
12-4 Items in the Extended Setup Menu	122
Chapter 13 Setup Utility Menu Functions	145
13-1 Overview of Setup Utility Menu Functions	145
13-1-1 Using Memory Stick Data	145
Chapter 14 Maintenance and Inspection	149
14-1 Removing a Cassette When Tape Slack Occurs	149
14-2 Head Cleaning	149
14-3 Error Messages	150
14-4 Moisture Condensation	152
14-5 Regular Checks	153
14-5-1 Digital Hours Meter	153
14-5-2 Maintenance Timings	154
Appendix	155
Specifications	155

Sony DVWM2000 Product Manual (Operation Manual 1st Edition (Revised 6)) - Page 58

Executing DMC Playback, before the speed variation end point

Page 58 highlights