TP-Link OC200 Omada Controller Software 4.1.5Windows/Linux User Guide - Page 93

91

Chapter 4

Conﬁgure the Network with Omada SDN Controller

2.

Define packet-filtering criteria of the rule, including protocols, source, and destination, and

determine whether to forward the matched packets. Refer to the following table to configure the

required parameters.

Name

Enter a name to identify the ACL.

Status

Click the checkbox to enable the ACL.

Policy

Select the action to be taken when a packet matches the rule.

Permit

: Forward the matched packet.

Deny

: Discard the matched packet.

Protocols

Select one or more protocol types to which the rule applies from the drop-down

list. The default is All, indicating that packets of all protocols will be matched. When

you select one of TCP and UDP or both of them, you can set the IP address and port

number of a packet as packet-filtering criteria in the rule.

Bi-Directional

Click the checkbox to enable the switch to create another symmetric ACL with the

name “xxx_reverse”, where “xxx” is the name of the current ACL. The two ACLs target

at packets with the opposite direction of each other.

From the Source drop-down list, choose one of these options to specify the source of the packets

to which this ACL applies:

Network

Select the network you have created. If no networks have been created, you can select

the default network (LAN), or go to

Settings > Wired Networks > LAN

to create one.

The switch will examine whether the packets are sourced from the selected network.

IP Group

Select the IP Group you have created. If no IP Groups have been created, click

+Create

on this page or go to

Settings > Profiles > Groups

to create one. The switch will

examine whether the source IP address of the packet is in the IP Group.

IP-Port Group

Select the IP-Port Group you have created. If no IP-Port Groups have been created,

click

+Create



to create one. The

switch will examine whether the source IP address and port number of the packet are

in the IP-Port Group.

MAC Group

Select the MAC Group you have created. If no MAC Groups have been created, click

+Create



to create one. The switch

will examine whether the source MAC address of the packet is in the MAC Group.

From the Destination drop-down list, choose one of these options to specify the destination of the

packets to which this ACL applies:

Network

Select the network you have created. If no networks have been created, you can select

the default network (LAN), or go to

Settings > Wired Networks > LAN

to create one.

The switch will examine whether the packets are forwarded to the selected network.

IP Group

Select the IP Group you have created. If no IP Groups have been created, click

+Create



to create one. The switch will

examine whether the destination IP address of the packet is in the IP Group.

Section	Page
About this Guide	2
Omada SDN Controller Solution Overview	3
Overview of Omada SDN Controller Solution	4
Core Components	5
Get Started with Omada SDN Controller	10
Set Up Your Software Controller	11
Determine the Network Topology	11
Install Omada Software Controller	12
Start and Log In to the Omada Software Controller	14
Set Up Your Hardware Controller	19
Determine the Network Topology	19
Deploy Omada Hardware Controller	19
Start and Log in to the Controller	20
Set up Your Cloud-Based Controller	24
Manage Omada Managed Devices and Sites	25
Create Sites	26
Adopt Devices	30
For Omada Software Controller / Omada Hardware Controller	30
For Omada Cloud-Based Controller	42
Configure the Network with Omada SDN Controller	45
Navigate the UI	46
Modify the Current Site Configuration	49
Site Configuration	49
Services	49
Advanced Features	52
Device Account	54
Configure Wired Networks	55
Set Up an Internet Connection	55
Configure LAN Networks	69
Configure Wireless Networks	78
Set Up Basic Wireless Networks	78
Advanced Settings	84
WLAN Schedule	86
802.11 Rate Control	86
MAC Filter	87
Network Security	89
ACL	89
URL Filtering	97
Attack Defense	100
Transmission	105
Routing	105
NAT	108
Session Limit	111
Bandwidth Control	112
Configure VPN	116
Create Profiles	143
Time Range	143
Groups	144
Authentication	149
Portal	149
802.1X	180
MAC-Based Authentication	183
RADIUS Profile	184
Services	187
Dynamic DNS	187
SNMP	189
UPnP	190
SSH	191
Reboot Schedule	191
PoE Schedule	192
Export Data	193
Configure the Omada SDN Controller	195
Manage the Controller	196
General Settings	196
Mail Server	197
History Data Retention	199
Customer Experience Improvement Program	199
HTTPS Certificate	200
Access Port Config	200
Manage Your Controller Remotely via Cloud Access	202
Maintenance	204
Controller Status	204
User Interface	204
Backup & Restore	206
Migration	207
Site Migration	207
Controller Migration	212
Configure and Monitor Omada Managed Devices	219
Introduction to the Devices Page	220
Configure and Monitor the Gateway	224
Configure the Gateway	224
Monitor the Gateway	228
Configure and Monitor Switches	232
Configure Switches	232
Monitor Switches	249
Configure and Monitor EAPs	253
Configure EAPs	253
Monitor EAPs	263
Monitor and Manage the Clients	270
Manage Wired and Wireless Clients in Clients Page	271
Introduction to Clients Page	271
Using the Clients Table to Monitor and Manage the Clients	271
Using the Properties Window to Monitor and Manage the Clients	273
Manage Client Authentication in Hotspot Manager	278
Authorized Clients	278
Vouchers	278
Local Users	281
Operators	284
Monitor the Network	287
View the Status of Network with Dashboard	288
Page Layout of Dashboard	288
Explanation of Widgets	290
View the Statistics of the Network	298
Performance	298
Switch Statistics	301
Speed Test Statistics	303
Monitor the Network with Map	305
Topology	305
Map	307
View the Statistics During Specified Period with Insight	310
Known Clients	310
Past Portal Authorizations	311
Rogue APs	312
View and Manage Logs	314
Alerts	315
Events	316
Notifications	317
Manage Administrator Accounts of Omada SDN Controller	323
Introduction to User Accounts	324
Manage and Create Local User Accounts	325
Edit the Master Administrator Account	325
Create and Manage Administrator and Viewer	327
Manage and Create Cloud User Accounts	330
Set Up the Cloud Master Administrator	330

TP-Link OC200 Omada Controller Software 4.1.5Windows/Linux User Guide - Page 93

From the Source drop-down list, choose one of these options to specify the source of the packets

Page 93 highlights