Alpine IVA D106 Owner's Manual - Page 47

2.2ch (3WAY) System 2.2ch (3WAY) System / L+R Setting contents: LOW / MID-L / MID-H / HIGH 2.2ch (3WAY) System / L/R Setting contents: LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L / MID-H-R / HIGH-L / HIGH-R 4.2ch (FRONT/REAR/SUBW.) System 4.2ch (FRONT/REAR/SUBW.) System / L+R Setting contents: LOW (SUB-W) / MID (REAR) / HIGH (FRONT) 4.2ch (FRONT/REAR/SUBW.) System / L/R Setting contents: LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L / MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R Selecting the Cut-Off Frequency Touch [ ] or [ ] of FREQ., then select the cut-off frequency (crossover point). The adjustable bandwidth differs depending on the speaker (channel). 2.2ch (3WAY) System Setting contents: LOW / MID-L 20 Hz~200 Hz MID-H HIGH 20 Hz~20 kHz (1 kHz~20 kHz)*1/(20 Hz~20 kHz)*2 4.2ch (FRONT/REAR/SUBW.) System Setting contents: 20 Hz~200 Hz *1 When MAKER is selected, refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 47). *2 When USER is selected, refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 47). Adjusting the Level Touch [ ] or [ ] of LEVEL to adjust the level. Adjustable output level: -12 to 0 dB. Adjusting the Slope Touch [ ] or [ ] of SLOPE to adjust the slope. Adjustable slope: FLAT*, - 6 dB/oct., -12 dB/oct., -18 dB/oct., - 24 dB/oct. * FLAT can be set for the HIGH slope only when USER is selected in "Setting the Response Slope for the High Range Speaker (TW Setup)" (page 47). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With this unit, a message is displayed when the response slope for the high range speaker is set to FLAT. • Check the playback frequencies of the connected speakers before adjusting. • While adjusting the X-Over, you should consider the frequency response of the connected speakers. • About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer to the Owner's Manual of PXA-H100. Adjusting the Time Correction Before performing the following procedures, refer to "About Time Correction" (page 47). 1 Touch [ ] of T.CORR. The T.CORR adjustment screen appears. 2.2ch (3WAY) System FRONT L(Mid-L) / FRONT R(Mid-R) / REAR L(High-L) / REAR R(High-R) / SUBW. L / SUBW. R 4.2ch (FRONT/REAR/SUBW.) System FRONT L / FRONT R / REAR L / REAR R / SUBW. L / SUBW. R 2 Touch [ ] or [ ] of the desired speaker to adjust the distance. L = (distance to farthest speaker) - (distance to other speakers) Refer to "Time Correction Value List" on page 48. 3 Repeat steps 1 and 2 to set another speaker. By setting these values to make its sound reach the listening position at the same time as the sound of other speakers. Setting the Time Correction Unit (TCR Parameter) You can change the unit, (cm or inch) of time correction. Setting item: T.CORR PARAMETER Setting contents: CM / INCH CM: Time correction value is in cm. INCH: Time correction value is in inches. 45-EN