Brother International DreamMaker„ XE VE2200 Users Manual - English - Page 43

Using Threads that Unwind, Quickly

Get Brother International DreamMaker„ XE VE2200 PDF manuals and user guides View all Brother International DreamMaker„ XE VE2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

n Carefully pull the end of the thread that passed through the eye of the needle. was * If a loop was formed in the thread passed through the eye of the needle, carefully pull on the loop of thread through to the back of the needle. UPPER THREADING Note • Some needles cannot be threaded with the needle threader. In this case, instead of B using the needle threader after passing the thread through the needle bar thread guide (marked "6"), manually pass the thread 1 through the eye of the needle from the front to the back. Getting Ready Note • Pulling the loop of thread gently will avoid needle breakage. o Pull out about 5 cm (approx. 2 inches) the thread, and then pass it under the of presser foot toward the rear of the machine. → Raise the presser foot lever if the presser foot is lowered. a About 5 cm (approx. 2 inches) Memo • If the needle could not be threaded or the thread was not passed through the needle bar thread guides, perform the procedure again starting from step c. Then, pass the thread through the eye of the needle after step i. Using Threads that Unwind Quickly ■ Using the Spool Net If using transparent nylon monofilament thread, metallic thread, or other strong thread, place the included spool net over the spool before using it. When using specialty threads, threading must be done manually. If the spool net is too long, fold it once to match it to the spool size before placing it over the spool. a Spool net b Thread spool c Spool pin d Spool cap Memo • When threading the spool with the spool net on, make sure that 5 cm - 6 cm (approx. 2 inches - 2-1/2 inches) of thread are pulled out. • It may be necessary to adjust the thread tension when using the spool net. Basic operations B-41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
UPPER THREADING
Getting Ready
Basic operations
B-41
B
1
n
Carefully pull the end of the thread that was
passed through the eye of the needle.
*
If a loop was formed in the thread passed through
the eye of the needle, carefully pull on the loop of
thread through to the back of the needle.
o
Pull out about 5 cm (approx. 2 inches) of
the thread, and then pass it under the
presser foot toward the rear of the machine.
→
Raise the presser foot lever if the presser foot is
lowered.
a
About 5 cm (approx. 2 inches)
Using Threads that Unwind
Quickly
■
Using the Spool Net
If using transparent nylon monofilament thread,
metallic thread, or other strong thread, place the
included spool net over the spool before using it.
When using specialty threads, threading must be
done manually.
If the spool net is too long, fold it once to match it to
the spool size before placing it over the spool.
Note
• Pulling the loop of thread gently will avoid
needle breakage.
Memo
• If the needle could not be threaded or the
thread was not passed through the needle
bar thread guides, perform the procedure
again starting from step
c
.
Then, pass the thread through the eye of
the needle after step
i
.
Note
• Some needles cannot be threaded with the
needle threader. In this case, instead of
using the needle threader after passing the
thread through the needle bar thread guide
(marked “6”), manually pass the thread
through the eye of the needle from the front
to the back.
a
Spool net
b
Thread spool
c
Spool pin
d
Spool cap
Memo
•
When threading the spool with the spool net
on, make sure that 5 cm - 6 cm (approx.
2 inches - 2-1/2 inches) of thread are pulled
out.
• It may be necessary to adjust the thread
tension when using the spool net.