Cisco ASR1006 Hardware Installation Guide - Page 158

Using show Commands to Verify the SIP and SPA Status

Get Cisco ASR1006 - ASR 1006 Modular Expansion Base PDF manuals and user guides
UPC - 882658196423
View all Cisco ASR1006 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 158 highlights

Checking the Installation Chapter 6 Installing and Removing a SPA Step 2 If the SIPs and SPAs have not become active within three minutes, refer to the system console messages as follows: • If a SIP or SPA is undergoing a field-programmable device (FPD) upgrade, then console messages will indicate that the FPD process has been initiated. The upgrade process might take several minutes. Use the show upgrade fpd progress command to obtain information about the FPD process. SIPs or SPAs that undergo an FPD upgrade will automatically be rebooted. Return to Step 1. • If there is no indication that an FPD upgrade is under way, see Chapter 7, "Troubleshooting the Installation." Using show Commands to Verify the SIP and SPA Status The following procedure uses show commands to verify that the new SPAs are configured and operating correctly. Step 1 Step 2 Step 3 Step 4 Use the show running-config command to display the system configuration. Verify that the configuration includes the new SPA interfaces. Display all of the current SPAs and a summary of their status using the show hw-module subslot all oir command. Display information about the installed SIPs using the show diag command. Use the show hw-module subslot all fpd command to verify the FPD version information of the SPAs installed in the system. Note If a SPA does not meet the minimum FPD version required, it will be updated automatically. If the update fails, the failing SPA will be powered down and an error message will be reported on the system console. Step 5 For more information about FPD upgrades, refer to the "Upgrading Field-Programmable Devices" chapter of the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide. Use the show version command to obtain a few details on the installed SIPs and interfaces. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 6-8 OL-14126-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
6-8
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide
OL-14126-12
Chapter 6
Installing and Removing a SPA
Checking the Installation
Step 2
If the SIPs and SPAs have not become active within three minutes, refer to the system console messages
as follows:
•
If a SIP or SPA is undergoing a field-programmable device (FPD) upgrade, then console messages
will indicate that the FPD process has been initiated. The upgrade process might take several
minutes. Use the
show upgrade fpd progress
command to obtain information about the FPD
process. SIPs or SPAs that undergo an FPD upgrade will automatically be rebooted. Return to
Step 1
.
•
If there is no indication that an FPD upgrade is under way, see
Chapter 7, “Troubleshooting the
Installation.”
Using show Commands to Verify the SIP and SPA Status
The following procedure uses
show
commands to verify that the new SPAs are configured and operating
correctly.
Step 1
Use the
show running-config
command to display the system configuration. Verify that the
configuration includes the new SPA interfaces.
Step 2
Display all of the current SPAs and a summary of their status using the
show hw-module subslot all oir
command.
Step 3
Display information about the installed SIPs using the
show diag
command.
Step 4
Use the
show hw-module subslot all fpd
command to verify the FPD version information of the SPAs
installed in the system.
Note
If a SPA does not meet the minimum FPD version required, it will be updated automatically. If
the update fails, the failing SPA will be powered down and an error message will be reported on
the system console.
For more information about FPD upgrades, refer to the “Upgrading Field-Programmable
Devices” chapter of the
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software
Configuration Guide.
Step 5
Use the
show version
command to obtain a few details on the installed SIPs and interfaces.