Epson ActionLaser 1100 User Manual - Page 42

Ready, in the Read This First, Troubleshooting

Get Epson ActionLaser 1100 PDF manuals and user guides View all Epson ActionLaser 1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Be sure the printer is level. Do not load more than 100 sheets of paper in the tray. Be sure to adjust the paper guides so that the paper can slide in and out freely. Never let more than 50 sheets accumulate in the exit tray. Try turning over the stack of paper in the tray. Most paper packages indicate which side should be face up. Do not load paper while the printer is operating. The Ready light does not turn on when you turn the printer on Open the printer's front cover and make sure the toner cartridge is installed securely. Turn off the printer and check the power cable connections between the printer and the electrical outlet; then turn the printer back on. If the electrical outlet is controlled by an outside source such as a wall switch, make sure the switch is turned on or plug another electrical device into the outlet to make sure the outlet is operating properly. The Ready light is on but nothing prints Your computer may not be properly connected to the printer. Perform the procedure "Testing the computer-toprinter connection" in the Read This First guide. The interface cable may not be plugged in securely. Check both ends of the cable between the printer and the computer. Be sure to secure the connector using the wire retaining clips. Troubleshooting 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Be sure the printer is level.
Do not load more than 100 sheets of paper in the tray.
Be sure to adjust the paper guides so that the paper can
slide in and out freely.
Never let more than 50 sheets accumulate in the exit tray.
Try turning over the stack of paper in the tray. Most paper
packages indicate which side should be face up.
Do not load paper while the printer is operating.
The
Ready
light does not turn on when you turn the printer on
Open the printer’s front cover and make sure the toner
cartridge is installed securely.
Turn off the printer and check the power cable connections
between the printer and the electrical outlet; then turn the
printer back on.
If the electrical outlet is controlled by an outside source such
as a wall switch, make sure the switch is turned on or plug
another electrical device into the outlet to make sure the outlet
is operating properly.
The
Ready
light is on but nothing prints
Your computer may not be properly connected to the printer.
Perform the procedure “Testing the computer-toprinter
connection”
in the Read This First
guide.
The interface cable may not be plugged in securely. Check both
ends of the cable between the printer and the computer. Be
sure to secure the connector using the wire retaining clips.
Troubleshooting
3-3