Fluke 199C/S FE 192,196,199 C Users Manual - Page 101

Troubleshooting, The Test Tool Shuts Down After A Few Seconds

Get Fluke 199C/S PDF manuals and user guides View all Fluke 199C/S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Troubleshooting The Test Tool Does Not Start Up • The batteries may be completely empty. In this case the test tool will not start up, even if it is powered by the battery charger. Charge the batteries first: power the test tool with the battery charger without turning it on. Wait about 15 minutes and try turning on the test tool again. The Test Tool Shuts Down After A Few Seconds • The batteries may be empty. Check the battery symbol at the top right of the screen. A symbol indicates that the batteries are empty and must be charged. The Screen Remains Black • Make sure that the test tool is on. • You might have a problem with the screen contrast. Press , then press . Now you can use the arrow keys to adjust the contrast. 8 Maintaining the Test Tool Troubleshooting The Operation Time Of Fully Charged Batteries Is Too Short • The batteries may be in poor condition. Refresh the batteries to optimize the condition of the batteries again. It is advised to refresh the batteries about four times a year. The Printer Does Not Print • Make sure that the interface cable is properly connected between the test tool and the printer. • Make sure that you have selected the correct printer type. (See Chapter 6.) • Make sure that the baud rate matches with the printer. If not, select another baud rate. (See Chapter 6.) • If you are using the PAC91 (Print Adapter Cable), make sure that it is turned on. 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Maintaining the Test Tool
Troubleshooting
8
93
Troubleshooting
The Test Tool Does Not Start Up
•
The batteries may be completely empty. In this case
the test tool will not start up, even if it is powered by
the battery charger. Charge the batteries first: power
the test tool with the battery charger without turning it
on. Wait about 15 minutes and try turning on the test
tool again.
The Test Tool Shuts Down After A Few Seconds
•
The batteries may be empty. Check the battery
symbol at the top right of the screen. A
symbol
indicates that the batteries are empty and must be
charged.
The Screen Remains Black
•
Make sure that the test tool is on.
•
You might have a problem with the screen contrast.
Press
, then press
. Now you can use
the
arrow keys to adjust the contrast.
The Operation Time Of Fully Charged Batteries
Is Too Short
•
The batteries may be in poor condition. Refresh the
batteries to optimize the condition of the batteries
again. It is advised to refresh the batteries about four
times a year.
The Printer Does Not Print
•
Make sure that the interface cable is properly
connected between the test tool and the printer.
•
Make sure that you have selected the correct printer
type. (See Chapter 6.)
•
Make sure that the baud rate matches with the printer.
If not, select another baud rate.
(See Chapter 6.)
•
If you are using the PAC91 (Print Adapter Cable),
make sure that it is turned on.