Fluke 199C/S FE 192,196,199 C Users Manual - Page 85

Using the Tilt Stand, Resetting the Test Tool, Suppressing Key Labels and Menu's

Get Fluke 199C/S PDF manuals and user guides View all Fluke 199C/S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Using the Tilt Stand The test tool is equipped with a tilt stand, allowing viewing from an angle while placed on a table. From this position you can access the OPTICAL PORT at the side of the test tool. The typical position is shown in Figure 46. Figure 46. Using the Tilt Stand 7 Tips Using the Tilt Stand Resetting the Test Tool If you want to reset the test tool to the factory settings, do the following: 1 Turn the test tool off. 2 Press and hold. 3 Press and release. The test tool turns on, and you should hear a double beep, indicating the reset was successful. 4 Release. Suppressing Key Labels and Menu's You can hide a menu or key label at any time: Hide any key label or menu. To display menus or key labels, press one of the yellow menu keys, e.g. the SCOPE key. 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Tips
Using the Tilt Stand
7
77
Using the Tilt Stand
The test tool is equipped with a tilt stand, allowing viewing
from an angle while placed on a table. From this position
you can access the OPTICAL PORT at the side of the test
tool. The typical position is shown in Figure 46.
Figure 46. Using the Tilt Stand
Resetting the Test Tool
If you want to reset the test tool to the factory settings, do
the following:
1
Turn the test tool off.
2
Press and hold.
3
Press and release.
The test tool turns on, and you should hear a double beep,
indicating the reset was successful.
4
Release.
Suppressing Key Labels and Menu’s
You can hide a menu or key label at any time:
Hide any key label or menu.
To display menus or key labels, press one of the yellow
menu keys, e.g. the
SCOPE
key.