Fluke 199C/S FE 192,196,199 C Users Manual - Page 20

Displaying an Unknown Signal with, Connect-and-View™, Perform an Auto Set.

Get Fluke 199C/S PDF manuals and user guides View all Fluke 199C/S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Fluke 192B - 196B/C - 199B/C Users Manual Displaying an Unknown Signal with Connect-and-View™ The Connect-and-View feature lets the test tool display complex, unknown signals automatically. This function optimizes the position, range, time base, and triggering and assures a stable display of virtually any waveform. If the signal changes, the setup is automatically adjusted to maintain the best display result. This feature is especially useful for quickly checking several signals. To enable the Connect-and-View feature, do the following: 1 Perform an Auto Set. AUTO appears at the top right of the screen. The bottom line shows the range, the time base, and the trigger information. The waveform identifier (A) is visible on the bottom right side of the screen, as shown in Figure 7. The input A zero - icon ( ) at the left side of the screen identifies the ground level of the waveform. 2 Press a second time to select the manual range again. MANUAL appears at the top right of the screen. Figure 7. The Screen After an Auto Set Use the light-gray RANGE, TIME and MOVE keys at the bottom of the keypad to change the view of the waveform manually. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Fluke 192B - 196B/C - 199B/C
Users Manual
12
Displaying an Unknown Signal with
Connect-and-View™
The Connect-and-View feature lets the test tool display
complex, unknown signals automatically. This function
optimizes the position, range, time base, and triggering
and assures a stable display of virtually any waveform. If
the signal changes, the setup is automatically adjusted to
maintain the best display result. This feature is especially
useful for quickly checking several signals.
To enable the Connect-and-View feature, do the following:
1
Perform an Auto Set.
AUTO
appears at
the top right of the screen.
The bottom line shows the range, the time base, and the
trigger information.
The waveform identifier (
A
) is visible on the bottom right
side of the screen, as shown in Figure 7. The input A zero
icon (
-
) at the left side of the screen identifies the ground
level of the waveform.
2
Press a second time to select the
manual range again.
MANUAL
appears
at the top right of the screen.
Figure 7. The Screen After an Auto Set
Use the light-gray
RANGE
,
TIME
and
MOVE
keys at the
bottom of the keypad to change the view of the waveform
manually.