Garmin GPSMAP 298C Owner's Manual - Page 8

No signal strength bars, To graphically initialize the GPSMAP 292/298 - gpsmap 298

Get Garmin GPSMAP 298C - Marine GPS Receiver PDF manuals and user guides
UPC - 753759052072
View all Garmin GPSMAP 298C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

BASIC OPERATION > TURNING ON THE GPSMAP 292/298 To graphically initialize the GPSMAP 292/298: 1. Press and hold ADJ/MENU for the Main Menu. Press up or down on the ROCKER until the GPS tab is highlighted, and then press ADJ/MENU once. 2. Using the ROCKER, highlight Initialize Position, and press ENTER. The Initialize Position Page appears, prompting you to select your approximate location with the map pointer. 3. Use the ROCKER to move the map pointer to your approximate location within 200 miles. If you have difficulty identifying your location, press and release the RANGE Down key to see the next lower map range. 4. After you have determined your approximate location on the map, press ENTER. NOTE: This does not calibrate the unit in any way, rather it helps to speed up the initial satellite acquisition. If the unit shows "Ready for Navigation" during this process, it is not necessary to initialize the unit. The unit now begins searching for the appropriate satellites for your region and should acquire a fix within a few minutes. When viewing the GPS tab on the Main Menu, a signal strength bar for each satellite in view appears on the bottom of the page, with the appropriate satellite number under each bar. • No signal strength bars-the receiver is looking for the satellites indicated. • Hollow signal strength bars-the receiver has found the indicated satellite(s) and is collecting data. • Solid signal strength bars-the receiver is ready to use. When the receiver has collected information from at least three satellites, the top of the screen shows "Ready for Navigation", and the GPSMAP 292/298 is ready for use. 2 GPSMAP 292/298 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2
GPSMAP 292/298 Owner’s Manual
B
ASIC
O
PERATION
>
T
URNING
ON
THE
GPSMAP 292/298
To graphically initialize the GPSMAP 292/298:
1.
Press and hold
ADJ/MENU
for the Main Menu. Press up or
down on the
ROCKER
until the
GPS
tab is highlighted, and
then press
ADJ/MENU
once.
2.
Using the
ROCKER
, highlight
Initialize Position
, and press
ENTER
. The Initialize Position Page appears, prompting
you to select your approximate location with the map
pointer.
3.
Use the
ROCKER
to move the map pointer to your
approximate location within 200 miles. If you have difficulty
identifying your location, press and release the
RANGE
Down
key to see the next lower map range.
4.
After you have determined your approximate location on the
map, press
ENTER
.
NOTE:
This does not calibrate the unit in any way, rather it
helps to speed up the initial satellite acquisition. If the unit
shows “Ready for Navigation” during this process, it is not
necessary to initialize the unit.
The unit now begins searching for the appropriate satellites for
your region and should acquire a fix within a few minutes. When
viewing the GPS tab on the Main Menu, a signal strength bar for
each satellite in view appears on the bottom of the page, with the
appropriate satellite number under each bar.
•
No signal strength bars
—the receiver is looking for the
satellites indicated.
•
Hollow signal strength bars
—the receiver has found the
indicated satellite(s) and is collecting data.
•
Solid signal strength bars
—the receiver is ready to use.
When the receiver has collected information from at least three
satellites, the top of the screen shows “Ready for Navigation”, and
the GPSMAP 292/298 is ready for use.