HP ProLiant 2500 Compaq ProLiant 2500 Family of Servers Maintenance and Servic - Page 89

Starting DAAD, DAAD Diagnostic Messages, Accelerator board not detected

Get HP ProLiant 2500 PDF manuals and user guides View all HP ProLiant 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

3-37 Starting DAAD To start DAAD: 1. Insert the DAAD diskette into drive A and reboot the system. If you are at the DOS prompt, enter the following: A:DAAD 2. A dialog box displays indicating the version of DAAD installed. Press the Enter key to continue, or press the Esc key to exit without continuing. 3. If you continue, a Please Wait panel displays indicating that DAAD is identifying the system parameters. DAAD gathers all the information it can from all of the array controllers in the system. The time it takes to gather this information depends on the size of your system. CAUTION: Do not cycle the power because the utility must perform low-level operations that, if interrupted, could cause the controller to revert to a previous level of firmware if the firmware was soft-upgraded. 4. Another Please Wait panel displays to indicate that the utility is identifying the ROM version. When this is complete, the main DAAD screen displays. NOTE: To generate a DAAD report without starting the interactive portion of the utility, at the DOS prompt enter the following: DAAD filename where filename is the name of the file or report. DAAD Diagnostic Messages The following is a description of the diagnostic messages that may be displayed in the dialog box of the Diagnosis menu. Included with each message is a probable cause and a probable solution or troubleshooting routine. To view the problems detected by DAAD, select the Diagnosis button. If DAAD found no problems, a message, "No Problems Detected," will display. Accelerator board not detected The array controller board did not detect the presence of a configured array accelerator board. Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-37
Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide
Starting DAAD
To start DAAD:
1.
Insert the DAAD diskette into drive A and reboot the system. If you are at the DOS
prompt, enter the following:
A:DAAD
2.
A dialog box displays indicating the version of DAAD installed. Press the
Enter
key to continue, or press the
Esc
key to exit without continuing.
3.
If you continue, a Please Wait panel displays indicating that DAAD is identifying
the system parameters.
DAAD gathers all the information it can from all of the array controllers in the
system. The time it takes to gather this information depends on the size of your
system.
CAUTION:
Do not cycle the power because the utility must
perform low-level operations that, if interrupted, could cause
the controller to revert to a previous level of firmware if the
firmware was soft-upgraded.
4.
Another Please Wait panel displays to indicate that the utility is identifying the
ROM version. When this is complete, the main DAAD screen displays.
NOTE:
To generate a DAAD report without starting the
interactive portion of the utility, at the DOS prompt enter the
following:
DAAD
filename
where
filename
is the name of the file or report.
DAAD Diagnostic Messages
The following is a description of the diagnostic messages that may be displayed in the
dialog box of the Diagnosis menu. Included with each message is a probable cause and a
probable solution or troubleshooting routine.
To view the problems detected by DAAD, select the Diagnosis button. If DAAD found no
problems, a message, "No Problems Detected," will display.
Accelerator board not detected
The array controller board did not detect the presence of a configured array
accelerator board.