HP ProLiant 2500 Compaq ProLiant 2500 Family of Servers Maintenance and Servic - Page 92

Controller detected. CMOS not present, Controller firmware needs upgrading

Get HP ProLiant 2500 PDF manuals and user guides View all HP ProLiant 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

3-40 Diagnostic Tools CMOS present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. Compatibility port problem detected You have the compatibility port configured for this array controller. When DAAD was verifying this interface, a serious problem was detected. A hardware problem has occurred and you should replace the array controller. Configuration signature is zero DAAD detected that nonvolatile RAM contains a configuration signature that is zero. Old versions of the System Configuration Utility could cause this. Run the latest version of System Configuration Utility to configure the controller and nonvolatile RAM. Configuration signature mismatch The array accelerator board has been configured for a different array controller board. The configuration signature on the array accelerator board does not match the one stored on the array controller board. To recognize the array accelerator board, run the System Configuration Utility. Controller communication failure occurred DAAD was unable to successfully issue commands to the controller in this slot. Controller detected. CMOS not present The EISA nonvolatile RAM is not configured. Run the System Configuration Utility to configure the nonvolatile RAM. Controller firmware needs upgrading The controller firmware is below the latest recommended version. Call your Authorized Compaq Reseller to obtain the latest upgraded firmware.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-40
Diagnostic Tools
CMOS present, controller not detected
EISA nonvolatile RAM has a configuration for an array controller but there is no board in
this slot. Either a board has been removed from the system or a board has been placed in
the wrong slot.
Place the array controller in the proper slot or run the System Configuration Utility to re-
configure nonvolatile RAM to reflect the removal or new position.
Compatibility port problem detected
You have the compatibility port configured for this array controller. When DAAD was
verifying this interface, a serious problem was detected.
A hardware problem has occurred and you should replace the array controller.
Configuration signature is zero
DAAD detected that nonvolatile RAM contains a configuration signature that is zero. Old
versions of the System Configuration Utility could cause this.
Run the latest version of System Configuration Utility to configure the controller and
nonvolatile RAM.
Configuration signature mismatch
The array accelerator board has been configured for a different array controller board. The
configuration signature on the array accelerator board does not match the one stored on the
array controller board.
To recognize the array accelerator board, run the System Configuration Utility.
Controller communication failure occurred
DAAD was unable to successfully issue commands to the controller in this slot.
Controller detected. CMOS not present
The EISA nonvolatile RAM is not configured.
Run the System Configuration Utility to configure the nonvolatile RAM.
Controller firmware needs upgrading
The controller firmware is below the latest recommended version.
Call your Authorized Compaq Reseller to obtain the latest upgraded firmware.