NEC NP-UM330X eBeam Education Software Manual - Page 11

eBeam Classic Setup, To secure brackets to the receiver, position the desired bracket over

Get NEC NP-UM330X PDF manuals and user guides View all NEC NP-UM330X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

© 2011 Luidia, Incorporated eBeam Classic Setup The following describes a typical setup for the eBeam USB or Bluetooth Wireless receivers and related hardware. Connect your projector to your computer. Turn on your projector and align/focus the image on the board. Connect the eBeam USB cable to your eBeam Receiver. Attach the eBeam Receiver mounting bracket to the board. The eBeam package contains the following receiver mounting options.  Suction cups  Command adhesive  Magnetic mounting brackets The eBeam Receiver is pre-attached to the suction cup mounting bracket. To detach any of the mounting brackets from the eBeam Receiver, position thumbs at bottom corners of the bracket and push up; the bracket should easily snap off. To secure brackets to the receiver, position the desired bracket over the back of the receiver and snap it into place. To permanently fasten the receiver, use the clear mounting bracket -- the one without suction cups. Fasten the receiver to the mounting surface through the holes in the clear mounting bracket. Install the AA battery in your eBeam Stylus. Page 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Page 11
© 2011 Luidia, Incorporated
eBeam Classic Setup
The following describes a typical setup for the eBeam USB or Bluetooth Wireless receivers
and related hardware.
Connect your projector to your computer.
Turn on your projector and align/focus the image on the board.
Connect the eBeam USB cable to your eBeam Receiver.
Attach the eBeam Receiver mounting bracket to the board.
The eBeam package contains the following receiver mounting options.
Suction cups
Command adhesive
Magnetic mounting brackets
The eBeam Receiver is pre-attached to the suction cup mounting
bracket. To detach any of the mounting brackets from the eBeam
Receiver, position thumbs at bottom corners of the bracket and push
up; the bracket should easily snap off.
To secure brackets to the receiver, position the desired bracket over
the back of the receiver and snap it into place. To permanently fasten
the receiver, use the clear mounting bracket -- the one without suction
cups. Fasten the receiver to the mounting surface through the holes in
the clear mounting bracket.
Install the AA battery in your
eBeam Stylus
.