3Com 4800G Getting Started Guide - Page 67

Loading host software, the following information

Get 3Com 4800G - Switch PDF manuals and user guides
UPC - 662705534183
View all 3Com 4800G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Figure 65 Page for file sending Local Software Loading 67 9 After the download completes, the system displays the following information: Loading ...CCCCCCCCCC done! n You do not need to reset the HyperTerminal's baud rate and thus can skip the last step if you have chosen 9600 bps. In this case, the system displays the prompt "BootROM is updating now done!" instead of the prompt "Your baudrate should be set to 9600 bps again! Press enter key when ready". 10 Reset HyperTerminal's baud rate to 9600 bps (refer to Step 4 and 5). Then, press any key as prompted. The system will display the following information to show the loading process is done. Bootrom updating done! Loading host software 1 Select 1 in Boot Menu to load the host software of the switch. The system displays the following information: 1. Set TFTP protocol parameter 2. Set FTP protocol parameter 3. Set XMODEM protocol parameter 0. Return to boot menu Enter your choice(0-3):3 To load the host software through XModem, select 3. The subsequent steps are the same as those for loading the Boot ROM program, except that the system gives the prompt for host software loading instead of Boot ROM loading.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Local Software Loading
67
Figure 65
Page for file sending
9
After the download completes, the system displays the following information:
Loading ...CCCCCCCCCC done!
n
You do not need to reset the HyperTerminal’s baud rate and thus can skip the last
step if you have chosen 9600 bps. In this case, the system displays the prompt
“BootROM is updating now
.....................................
done!” instead of the prompt
“Your baudrate should be set to 9600 bps again! Press enter key when ready”.
10
Reset HyperTerminal’s baud rate to 9600 bps (refer to Step 4 and 5). Then, press
any key as prompted. The system will display the following information to show
the loading process is done.
Bootrom updating
.....................................
done!
Loading host software
1
Select
1
in Boot Menu to load the host software of the switch. The system displays
the following information:
1. Set TFTP protocol parameter
2. Set FTP protocol parameter
3. Set XMODEM protocol parameter
0. Return to boot menu
Enter your choice(0-3):3
To load the host software through XModem, select
3
.
The subsequent steps are the same as those for loading the Boot ROM program,
except that the system gives the prompt for host software loading instead of Boot
ROM loading.