AIWA NSX-999 Operating Instructions - Page 46

Recording, From The Radio Or, Connected, Equipment

Get AIWA NSX-999 PDF manuals and user guides View all AIWA NSX-999 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

1 DOLBY NR b 3 11 REV MODE (DECK /2) b 46 RECORDING FROM THE RADIO OR CONNECTED EQUIPMENT Preparation " Wind up the tape to the point where recording will start. q Use normal (type I) or Cr02 (type II) tapes. 1 Insert the tape to be recorded on into deck 2. Press the EJECT A mark to open the cassette holder. Insert the tape with the side to be recorded on first facing you and the exposed side down. Push the cassette holder to close it. 2 Set DOLBY NR. To record with DOLBY NR: Press the DOLBY NR button to turn on the Dolby NR. The 00 NR indicator will light. To record without DOLBY NR: Press the DOLBY NR button to turn off the Dolby NR, The 00 NR indicator will go off. 3 Set the reverse mode. Each time the REV MODE button is pressed, the reverse mode changes. To record on one side only, turn on =. To record on both sides, turn on =>. 4 Press the TUNEFUBAND or VIDEO/AUX button to select the source to be recorded from and play it. 5 Press the q REC/REC MUTE button to start recording. When you use the remote control to start recording, first press the q/0 REC/REC MUTE button and then press the 4button within 2 seconds. To stop recording Press the s button. To pause recording Press the II button. To resume recording, press it again. TO INSERT 4-SECOND BLANK SPACES Blank spaces in the recording allow you to activate the Music Sensor function (see page 38). (Applicable when the source is TUNER or VIDEO/AUX.) 1 Press the q REC/REC MUTE button during recording or from recording pause mode. REC flashes in the display for 4 seconds and the tape runs without recording. After 4 seconds the deck enters recording pause mode. 2 Press the II button to resume recording.. To insert a blank space of less than 4 seconds After pressing the q REC/REC MUTE button, press it again while REC is blinking to resume recording. To insert a blank space of more than 4 seconds After the deck enters recording pause mode, press the q REC/ REC MUTE button again. Each time it is pressed, a4-second blank space is added.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
1
DOLBY NR
b
3
1
1
REV MODE
(DECK /2)
b
RECORDING
FROM THE RADIO OR
CONNECTED
EQUIPMENT
Preparation
“
Wind up the tape to the point where recording will start.
Use normal (type I) or Cr02 (type II) tapes.
1
2
3
4
5
Insert the tape to be recorded
on into deck 2.
Press the EJECT A mark to open the cassette holder.
Insert the tape with the side to be recorded on first facing you
and the exposed side down.
Push the cassette holder to close it.
Set DOLBY
NR.
To record with DOLBY
NR:
Press the DOLBY NR button to turn
on the Dolby NR. The 00 NR indicator will light.
To record without DOLBY NR: Press the DOLBY NR button to
turn off the Dolby NR, The 00 NR indicator will go off.
Set the reverse
mode.
Each time the REV MODE button is pressed, the reverse mode
changes.
To record on one side only, turn on =.
To record on both sides, turn on =>.
Press the TUNEFUBAND
or VIDEO/AUX
button
to
select the source
to be recorded
from and play it.
Press the
REC/REC
MUTE button to start record-
ing.
When you use the remote control to start recording, first press
the
/0
REC/REC MUTE button and then press the 4-
button within 2 seconds.
To stop recording
Press the
button.
To pause recording
Press the II button.
To resume recording, press it again.
TO INSERT 4-SECOND
BLANK SPACES
Blank spaces in the recording allow you to activate the Music
Sensor function
(see page 38). (Applicable
when the source is
TUNER or VIDEO/AUX.)
1
Press the
REC/REC
MUTE button during record-
ing or from recording
pause mode.
REC flashes in the display for 4 seconds and the tape runs
without recording. After 4 seconds the deck enters recording
pause mode.
2
Press
the II button to resume
recording..
To insert a blank space of less than 4 seconds
After pressing the
REC/REC MUTE button, press it again while
REC is blinking to resume recording.
To insert a blank space of more than 4 seconds
After the deck enters recording pause mode, press the
REC/
REC MUTE button again. Each time it is pressed, a4-second blank
space is added.
46