Compaq ML530R Service Guide - Page 55

Processors, earlier in

Get Compaq ML530R - HP ProLiant - 128 MB RAM PDF manuals and user guides
UPC - 720591250300
View all Compaq ML530R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

2-40 Compaq ProLiant ML530 Servers Maintenance and Service Guide Processors Compaq ProLiant ML530 servers support up to two processors. The primary processor is located closest to the edge of the system board. IMPORTANT: Use only 133-MHz front-side bus Pentium III Xeon processors with gold-colored heat sinks. Processors with other colored heat sinks will not function properly in Compaq ProLiant ML530 servers. To remove a processor: 1. Perform the preparation procedures. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Remove the CPU fan air baffle. See "CPU Fan Air Baffle" earlier in this chapter. 4. Loosen the thumbscrew located on the top of the processor. 5. Lift and swing the levers outward. 6. Remove the processor from the slot . 1 2 2 3 Figure 2-33. Removing a processor Reverse steps 1 through 6 to replace the processor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
2-40
Compaq ProLiant ML530 Servers Maintenance and Service Guide
Processors
Compaq ProLiant ML530 servers support up to two processors. The primary processor is
located closest to the edge of the system board.
IMPORTANT:
Use only 133-MHz front-side bus Pentium III Xeon processors with gold-colored
heat sinks. Processors with other colored heat sinks will not function properly in Compaq ProLiant ML530
servers.
To remove a processor:
1.
Perform the preparation procedures. See
“
Powering Down the Server
”
earlier in this
chapter.
2.
Remove the access panel. See
“
Access Panel
”
earlier in this chapter.
3.
Remove the CPU fan air baffle. See
“
CPU Fan Air Baffle
”
earlier in this chapter.
4.
Loosen the thumbscrew
located on the top of the processor.
5.
Lift and swing the levers
outward.
6.
Remove the processor from the slot
.
1
2
3
2
Figure 2-33.
Removing a processor
Reverse steps 1 through 6 to replace the processor.