Compaq ML530R Service Guide - Page 60

Power On/Standby Switch

Get Compaq ML530R - HP ProLiant - 128 MB RAM PDF manuals and user guides
UPC - 720591250300
View all Compaq ML530R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Removal and Replacement Procedures 2-45 Power On/Standby Switch To remove the Power On/Standby switch and cable assembly: 1. Perform the preparation procedures. See "Powering Down the Server" earlier in this chapter. 2. Remove the access panel. See "Access Panel" earlier in this chapter. 3. Remove the hard drive fan air baffle. See "Hard Drive Fan Air Baffle" earlier in this chapter. 4. Disconnect the power switch cable from the power backplane board , and feed it through the cable grommet. 5. Press the tabs on both sides of the switch to release it. NOTE: A 4-mm flat-blade screwdriver can be used to assist with pressing the tabs. 6. With the tabs released, pull the switch and cable out the front of the bezel . 1 3 2 2 Figure 2-38. Removing the Power On/Standby switch Reverse steps 1 through 6 to replace the Power On/Standby switch.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Removal and Replacement Procedures
2-45
Power On/Standby Switch
To remove the Power On/Standby switch and cable assembly:
1.
Perform the preparation procedures. See
“
Powering Down the Server
”
earlier in this
chapter.
2.
Remove the access panel. See
“
Access Panel
”
earlier in this chapter.
3.
Remove the hard drive fan air baffle. See
“
Hard Drive Fan Air Baffle
”
earlier in this
chapter.
4.
Disconnect the power switch cable from the power backplane board
, and feed it through
the cable grommet.
5.
Press the tabs
on both sides of the switch to release it.
NOTE:
A 4-mm flat-blade screwdriver can be used to assist with pressing the tabs.
6.
With the tabs released, pull the switch and cable out the front of the bezel
.
2
1
2
3
Figure 2-38.
Removing the Power On/Standby switch
Reverse steps 1 through 6 to replace the Power On/Standby switch.