Compaq nx9010 Maintenance and Service Guide - Page 35

Removing an SDRAM Module - motherboard

Get Compaq nx9010 - Notebook PC PDF manuals and user guides View all Compaq nx9010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Removing an SDRAM Module (User-Replaceable) The notebook has no system memory built into its motherboard, but has 2 slots for SDRAM modules. One slot contains an SDRAM module that was factory installed. NOTE: HP Pavilion ze5300, ze5200, ze4300, ze4200, and ze4100, HP Compaq nx9010, nx9005 and nx9000, Compaq Evo Notebook N1050v and N1010v, and Compaq Presario 2500, 2100, and 1100 notebooks use only DDR266 SDRAM modules. Using the wrong type of module prevents the notebook from booting. CAUTION: Handle the SDRAM module only by its edges and provide proper grounding, or you might damage the module through electrostatic discharge. Required Equipment 1 Phillips screwdriver Removal Procedure 1. Unplug the AC adapter, if present, and then remove the battery. 2. On the bottom of the notebook, loosen the captive screws holding the SDRAM door, and then remove the door. 3. Press outward on the latches at the sides of the SDRAM module to release it (the SDRAM module pops up). 4. Carefully pull the SDRAM module out of the connector. Service Manual Figure 2-3. Removing an SDRAM Module HP Pavilion 4x00, HP Compaq nx9005 and nx9000, Compaq Evo Notebook N1050v and N1010v, and Compaq Presario 2100 and 1100 Models Removal and Replacement 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Service Manual
Removal and Replacement
2-5
Removing an SDRAM Module
(User-Replaceable)
The notebook has no system memory built into its motherboard, but has 2 slots for SDRAM modules.
One slot contains an SDRAM module that was factory installed.
NOTE:
HP Pavilion ze5300, ze5200, ze4300, ze4200, and ze4100, HP Compaq nx9010, nx9005
and nx9000, Compaq Evo Notebook N1050v and N1010v, and Compaq Presario 2500, 2100, and
1100 notebooks use only DDR266 SDRAM modules. Using the wrong type of module prevents the
notebook from booting.
CAUTION:
Handle the SDRAM module only by its edges and provide proper grounding,
or you might damage the module through electrostatic discharge.
Required Equipment
1 Phillips screwdriver
Removal Procedure
1.
Unplug the AC adapter, if present, and then remove the battery.
2.
On the bottom of the notebook, loosen the captive screws holding the SDRAM door, and
then remove the door.
3.
Press outward on the latches at the sides of the SDRAM module to release it (the SDRAM
module pops up).
4.
Carefully pull the SDRAM module out of the connector.
Figure 2-3. Removing an SDRAM Module
HP Pavilion 4x00, HP Compaq nx9005 and nx9000,
Compaq Evo Notebook N1050v and N1010v,
and Compaq Presario 2100 and 1100 Models