Compaq nx9010 Maintenance and Service Guide - Page 77

Removing the RJ11/1394 Connector Module

Get Compaq nx9010 - Notebook PC PDF manuals and user guides View all Compaq nx9010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Removing the RJ11/1394 Connector Module (Service Partners Only) NOTE: The following RJ11/1394 connector module removal instructions apply only to HP Pavilion 5x00, HP Compaq nx9010 and nx9008, and Compaq Presario 2500 models. Required Equipment Small flat-blade screwdriver Removal Procedure 1. Unplug the AC adapter, if present, and then remove the battery. 2. Remove these additional assemblies: • Hard disk drive (page 2-9) • Keyboard cover (page 2-13) • Keyboard (page 2-16) • Switchboard PCA (page 2-19) • Display assembly (page 2-23) • Top case (page 2-26) • Heat sink (page 2-40) 3. Remove the 4 screws that secure the hard disk drive guide to the bottom case. NOTE: The 4 screws that secure the hard disk drive guide are 2 different sizes. The screw in the upper left corner is a M2.5x6.0mm screw. The remaining 3 screws are M2.0×4.0mm screws. Make sure these screws are installed in the correct locations when reinstalling the hard disk drive guide. 4. Remove the hard disk drive guide. 5. Disconnect the modem cable from the motherboard. Service Manual Removal and Replacement 2-47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Service Manual
Removal and Replacement
2-47
Removing the RJ11/1394 Connector Module
(Service Partners Only)
NOTE:
The following RJ11/1394 connector module removal instructions apply only to
HP Pavilion 5x00, HP Compaq nx9010 and nx9008, and Compaq Presario 2500 models.
Required Equipment
Small flat-blade screwdriver
Removal Procedure
1.
Unplug the AC adapter, if present, and then remove the battery.
2.
Remove these additional assemblies:
•
Hard disk drive (page 2-9)
•
Keyboard cover (page 2-13)
•
Keyboard (page 2-16)
•
Switchboard PCA (page 2-19)
•
Display assembly (page 2-23)
•
Top case (page 2-26)
•
Heat sink (page 2-40)
3.
Remove the 4 screws that secure the hard disk drive guide to the bottom case.
NOTE:
The 4 screws that secure the hard disk drive guide are 2 different sizes. The screw in the upper
left corner is a M2.5x6.0mm screw. The remaining 3 screws are M2.0×4.0mm screws. Make sure these
screws are installed in the correct locations when reinstalling the hard disk drive guide.
4.
Remove the hard disk drive guide.
5.
Disconnect the modem cable from the motherboard.