Dell PowerEdge C6400 EMC Installation and Service Manual - Page 65

Installing the right midplane, Removing the left midplane

Get Dell PowerEdge C6400 PDF manuals and user guides View all Dell PowerEdge C6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Installing the right midplane Prerequisites NOTE: You must route the cables properly on the chassis to prevent them from being pinched or crimped. 1. Follow the safety guidelines listed in Safety instructions. Steps 1. Using the Phillips #1 screwdriver, connect and secure the power cables to the midplane. 2. Place the midplane into the chassis. 3. Using the Phillips #1 screwdriver, tighten the screws that secure the midplane to the chassis. Figure 52. Installing the right midplane Next steps 1. Reconnect all the disconnected cables. 2. Install the cooling fan cage. 3. Install the sleds into the enclosure. 4. Follow the procedure listed in After working inside your enclosure. Removing the left midplane Prerequisites NOTE: Observe the routing of the cables on the chassis as you remove them from the system. Route these cables properly when you replace them to prevent the cables from being pinched or crimped. 1. Follow the safety guidelines listed in Safety instructions.. 2. Follow the procedure listed in Before working inside your enclosure. 3. Remove all the sleds from the enclosure. 4. Remove the cooling fan cage. Installing and removing enclosure components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Installing the right midplane
Prerequisites
NOTE:
You must route the cables properly on the chassis to prevent them from being pinched or crimped.
1.
Follow the safety guidelines listed in
Safety instructions
.
Steps
1.
Using the Phillips #1 screwdriver, connect and secure the power cables to the midplane.
2.
Place the midplane into the chassis.
3.
Using the Phillips #1 screwdriver, tighten the screws that secure the midplane to the chassis.
Figure 52. Installing the right midplane
Next steps
1.
Reconnect all the disconnected cables.
2.
Install the cooling fan cage
.
3.
Install the sleds into the enclosure
.
4.
Follow the procedure listed in
After working inside your enclosure
.
Removing the left midplane
Prerequisites
NOTE:
Observe the routing of the cables on the chassis as you remove them from the system. Route these cables
properly when you replace them to prevent the cables from being pinched or crimped.
1.
Follow the safety guidelines listed in
Safety instructions
..
2.
Follow the procedure listed in
Before working inside your enclosure
.
3.
Remove all the sleds from the enclosure
.
4.
Remove the cooling fan cage
.
Installing and removing enclosure components
65