Dell PowerEdge C6400 EMC Installation and Service Manual - Page 82

Control panel, Removing the control panel

Get Dell PowerEdge C6400 PDF manuals and user guides View all Dell PowerEdge C6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Figure 72. Installing the backplane expander board Next steps 1. Reconnect all the disconnected cables. 2. Install the drive cage. 3. Follow the procedure listed in After working inside your enclosure. Control panel Removing the control panel Prerequisites NOTE: Observe the routing of the cables on the enclosure as you remove them. You must route these cables properly when you replace them to prevent the cables from being pinched or crimped. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your enclosure. 3. Remove all the drives. 4. Disconnect all the backplane cables from the linking board and chassis management board. 5. Remove the drive cage from the enclosure. 6. Disconnect control panel cables from the midplane. Steps 1. Using the Phillips #1 screwdriver, remove the screws that secure the control panel assembly to the enclosure. 2. Remove the cable from the cable retention clips. 3. Lift the control panel assembly away. 82 Installing and removing enclosure components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Figure 72. Installing the backplane expander board
Next steps
1.
Reconnect all the disconnected cables.
2.
Install the drive cage
.
3.
Follow the procedure listed in
After working inside your enclosure
.
Control panel
Removing the control panel
Prerequisites
NOTE:
Observe the routing of the cables on the enclosure as you remove them. You must route these cables properly
when you replace them to prevent the cables from being pinched or crimped.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your enclosure
.
3.
Remove all the drives
.
4.
Disconnect all the backplane cables from the linking board and chassis management board.
5.
Remove the drive cage from the enclosure
.
6.
Disconnect control panel cables from the midplane.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws that secure the control panel assembly to the enclosure.
2.
Remove the cable from the cable retention clips.
3.
Lift the control panel assembly away.
82
Installing and removing enclosure components