Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 100

Removing the Jumbo PERC card, Installing the PERC card

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Figure 67. Installing the PERC card Next steps 1. Connect the cable to the PERC card. 2. Install the PEM. 3. Follow the procedure listed in the After working inside your sled section. Removing the Jumbo PERC card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled section. 3. Remove the PEM. 4. Remove the air shroud from the system board. 5. Disconnect the cable that is connected to the Jumbo PERC card. Steps 1. Lift the two blue pull tags to raise the lever up on the Jumbo PERC card. 2. Holding both the blue pull tags, lift the Jumbo PERC card away from the sled. 3. Install the connector cap on the I/O connector of the Jumbo PERC card. 100 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 67. Installing the PERC card
Next steps
1.
Connect the cable to the PERC card.
2.
Install the PEM
.
3.
Follow the procedure listed in the
After working inside your sled
section.
Removing the Jumbo PERC card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
section.
3.
Remove the PEM
.
4.
Remove the air shroud from the system board
.
5.
Disconnect the cable that is connected to the Jumbo PERC card.
Steps
1.
Lift the two blue pull tags to raise the lever up on the Jumbo PERC card.
2.
Holding both the blue pull tags, lift the Jumbo PERC card away from the sled.
3.
Install the connector cap on the I/O connector of the Jumbo PERC card.
100
Installing and removing sled components