Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 112

Removing a mini Mezzanine card, Prerequisites, Steps, Next steps

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

2. Follow the procedure listed in the After working inside the sled section. Removing a mini Mezzanine card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside a sled section. 3. To remove the mini Mezzanine card from the system board, remove the PEM. 4. Remove the air shroud from the system board. Steps 1. Lift the blue pull tag to raise the lever up on the mini Mezzanine card. 2. Hold the lever and the edge of the mini Mezzanine card to lift the mini Mezzanine card away from the sled or PEM. Figure 80. Removing the mini Mezzanine card 3. Install the connector cap on the I/O connector of the mini Mezzanine card. NOTE: The PowerEdge MX840c sled supports HBA330 MMZ and Fiber channel MMZ which are installed in the mini Mezzanine card slot. Next steps 1. Install the mini Mezzanine card or the mini Mezzanine card blank. Installing a mini Mezzanine card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled section. Steps 1. Remove the connector cap on the I/O connector of the mini Mezzanine card. 2. Lift the blue pull tag to raise the lever up of the mini Mezzanine card. 3. Align the mini Mezzanine card connector, guides, and guide slots with the connector, guide, guide slots on the sled or PEM. 4. Lower and press the mini Mezzanine card until firmly seated. 112 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
2.
Follow the procedure listed in the
After working inside the sled
section.
Removing a mini Mezzanine card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside a sled
section.
3.
To remove the mini Mezzanine card from the system board,
remove the PEM
.
4.
Remove the air shroud from the system board
.
Steps
1.
Lift the blue pull tag to raise the lever up on the mini Mezzanine card.
2.
Hold the lever and the edge of the mini Mezzanine card to lift the mini Mezzanine card away from the sled or PEM.
Figure 80. Removing the mini Mezzanine card
3.
Install the connector cap on the I/O connector of the mini Mezzanine card.
NOTE:
The PowerEdge MX840c sled supports HBA330 MMZ and Fiber channel MMZ which are installed in the mini
Mezzanine card slot.
Next steps
1.
Install the mini Mezzanine card
or the
mini Mezzanine card blank
.
Installing a mini Mezzanine card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
section.
Steps
1.
Remove the connector cap on the I/O connector of the mini Mezzanine card.
2.
Lift the blue pull tag to raise the lever up of the mini Mezzanine card.
3.
Align the mini Mezzanine card connector, guides, and guide slots with the connector, guide, guide slots on the sled or PEM.
4.
Lower and press the mini Mezzanine card until firmly seated.
112
Installing and removing sled components