Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 58

Removing a drive from the drive carrier, Steps, Prerequisites

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Steps 1. Press the release button on the front of the drive carrier to open the release handle. 2. Insert the drive carrier into the drive slot and slide until the drive carrier connects with the backplane. 3. Close the release handle of the drive carrier to lock the drive in place. Figure 28. Installing a drive carrier Removing a drive from the drive carrier Prerequisites Follow the safety guidelines listed in the Safety instructions section. CAUTION: Mixing drives from previous generations of PowerEdge servers is not supported. Steps 1. Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier. 2. Lift the drive out of the drive carrier. 58 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Steps
1.
Press the release button on the front of the drive carrier to open the release handle.
2.
Insert the drive carrier into the drive slot and slide until the drive carrier connects with the backplane.
3.
Close the release handle of the drive carrier to lock the drive in place.
Figure 28. Installing a drive carrier
Removing a drive from the drive carrier
Prerequisites
Follow the safety guidelines listed in the
Safety instructions
section.
CAUTION:
Mixing drives from previous generations of PowerEdge servers is not supported.
Steps
1.
Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier.
2.
Lift the drive out of the drive carrier.
58
Installing and removing sled components