Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 98

If either the system board or iDRAC card fails, it is required to replace the system board and iDRAC

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

CAUTION: If either the system board or iDRAC card fails, it is required to replace the system board and iDRAC card simultaneously. Steps 1. Align the iDRAC card with the connector and guide pin on the system board. 2. Lower the iDRAC card on the system board connector and press the blue push points until the iDRAC card is firmly seated on the system board connector. Figure 64. Installing the iDRAC card NOTE: The iDRAC card is not swappable with other MX series sleds in the MX7000 enclosure. NOTE: The procedure to install a vFlash card is similar to installing a MicroSD card. Figure 65. Installing a vFlash card Next steps 1. Install the air shroud on the system board. 2. Install the PEM. 3. Follow the procedure listed in the After working inside your sled section. 98 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
CAUTION:
If either the system board or iDRAC card fails, it is required to replace the system board and iDRAC
card simultaneously.
Steps
1.
Align the iDRAC card with the connector and guide pin on the system board.
2.
Lower the iDRAC card on the system board connector and press the blue push points until the iDRAC card is firmly seated
on the system board connector.
Figure 64. Installing the iDRAC card
NOTE:
The iDRAC card is not swappable with other MX series sleds in the MX7000 enclosure.
NOTE:
The procedure to install a vFlash card is similar to
installing a MicroSD card
.
Figure 65. Installing a vFlash card
Next steps
1.
Install the air shroud on the system board
.
2.
Install the PEM
.
3.
Follow the procedure listed in the
After working inside your sled
section.
98
Installing and removing sled components