Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 45

Installing the sled into the enclosure, Next steps

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

CAUTION: If you are permanently removing the sled, install a blank. Operating the enclosure for extended periods of time without a blank installed can cause the enclosure to overheat. NOTE: The color of the I/O connector cover may differ. Next steps 1. Install the sled or blank into the enclosure. Installing the sled into the enclosure Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. Steps 1. Remove the I/O connector cover from the I/O connector(s) and store for future use. CAUTION: To prevent damage to the I/O connectors, do not touch the connectors or the connector pins. Figure 15. Removing the I/O connector cover from the sled NOTE: The color of the I/O connector cover may differ. 2. Press the blue lever button on the sled to release the lever. 3. Holding the sled with two hands, align the sled with the bay in the enclosure and slide the sled into the enclosure until firmly seated. 4. Rotate the lever up until it clicks into place and secures the sled in the enclosure. Installing and removing sled components 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
CAUTION:
If you are permanently removing the sled, install a blank. Operating the enclosure for extended
periods of time without a blank installed can cause the enclosure to overheat.
NOTE:
The color of the I/O connector cover may differ.
Next steps
1.
Install the sled or blank into the enclosure
.
Installing the sled into the enclosure
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
Steps
1.
Remove the I/O connector cover from the I/O connector(s) and store for future use.
CAUTION:
To prevent damage to the I/O connectors, do not touch the connectors or the connector pins.
Figure 15. Removing the I/O connector cover from the sled
NOTE:
The color of the I/O connector cover may differ.
2.
Press the blue lever button on the sled to release the lever.
3.
Holding the sled with two hands, align the sled with the bay in the enclosure and slide the sled into the enclosure until firmly
seated.
4.
Rotate the lever up until it clicks into place and secures the sled in the enclosure.
Installing and removing sled components
45