Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 43

After working inside your sled, Recommended tools, PowerEdge MX840c sled

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Steps 1. Power off the sled. 2. Remove the sled from the enclosure. 3. If applicable, install the I/O connector cover. CAUTION: To prevent damage to the I/O connectors on the sled, ensure that you cover the connectors when you remove the sled from the enclosure. 4. Remove the sled cover. After working inside your sled Prerequisites Follow the safety guidelines listed in the Safety instructions section. Steps 1. Install the sled cover. 2. If installed, remove the I/O connector cover on the sled. CAUTION: To prevent damage to the I/O connectors, do not touch the connectors or the connector pins. 3. Install the sled into the enclosure. 4. Power on the sled. NOTE: The sled iDRAC has to completely initialize first for the sled to power on. Recommended tools You need the following tools to perform the removal and installation procedures: ● Phillips #1 screwdriver ● Phillips #2 screwdriver ● Torx #T30 screwdriver ● 1/4 inch flat head screwdriver ● Wrist grounding strap PowerEdge MX840c sled The PowerEdge MX840c sled is a compute server unit that is installed into the PowerEdge MX7000 enclosure. The sled features quad processors, processor expansion module (PEM), memory modules, mezzanine cards, mini mezzanine card, PERC cards, and onboard storage (MicroSD card and M.2 SATA). Removing the sled from the enclosure Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Power off the sled. Steps 1. Press the blue lever button on the sled to release the lever. 2. Holding the release lever, slide the sled out of the enclosure. Installing and removing sled components 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Steps
1.
Power off the sled.
2.
Remove the sled from the enclosure.
3.
If applicable, install the I/O connector cover.
CAUTION:
To prevent damage to the I/O connectors on the sled, ensure that you cover the connectors when
you remove the sled from the enclosure.
4.
Remove the sled cover.
After working inside your sled
Prerequisites
Follow the safety guidelines listed in the
Safety instructions
section.
Steps
1.
Install the sled cover.
2.
If installed, remove the I/O connector cover on the sled.
CAUTION:
To prevent damage to the I/O connectors, do not touch the connectors or the connector pins.
3.
Install the sled into the enclosure.
4.
Power on the sled.
NOTE:
The sled iDRAC has to completely initialize first for the sled to power on.
Recommended tools
You need the following tools to perform the removal and installation procedures:
●
Phillips #1 screwdriver
●
Phillips #2 screwdriver
●
Torx #T30 screwdriver
●
1/4 inch flat head screwdriver
●
Wrist grounding strap
PowerEdge MX840c sled
The PowerEdge MX840c sled is a compute server unit that is installed into the PowerEdge MX7000 enclosure. The sled
features quad processors, processor expansion module (PEM), memory modules, mezzanine cards, mini mezzanine card, PERC
cards, and onboard storage (MicroSD card and M.2 SATA).
Removing the sled from the enclosure
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Power off the sled.
Steps
1.
Press the blue lever button on the sled to release the lever.
2.
Holding the release lever, slide the sled out of the enclosure.
Installing and removing sled components
43