Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 106

M.2 BOSS module, Removing the M.2 BOSS module

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Figure 73. Installing a MicroSD card Next steps 1. Install the IDSDM module. 2. Install the PEM. 3. Follow the procedure listed in the After working inside your sled section. M.2 BOSS module The M.2 BOSS module is a simple RAID solution designed specifically for booting a server's operating system. The module supports up to two 6 Gbps M.2 SATA cards. The M.2 BOSS module has a x8 connector using PCIe gen 3.0 x2 lanes. Removing the M.2 BOSS module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled. 3. Remove the PEM. 4. Remove the air shroud from the system board. Steps Hold the blue pull tag, and lift the M.2 BOSS module away from the sled. 106 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 73. Installing a MicroSD card
Next steps
1.
Install the IDSDM module
.
2.
Install the PEM
.
3.
Follow the procedure listed in the
After working inside your sled
section.
M.2 BOSS module
The M.2 BOSS module is a simple RAID solution designed specifically for booting a server's operating system. The module
supports up to two 6 Gbps M.2 SATA cards. The M.2 BOSS module has a x8 connector using PCIe gen 3.0 x2 lanes.
Removing the M.2 BOSS module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
.
3.
Remove the PEM
.
4.
Remove the air shroud from the system board
.
Steps
Hold the blue pull tag, and lift the M.2 BOSS module away from the sled.
106
Installing and removing sled components