Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 101

Installing the Jumbo PERC card, Removing the Jumbo PERC card

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Figure 68. Removing the Jumbo PERC card Next steps 1. Install the Jumbo PERC card. Installing the Jumbo PERC card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled section. 3. Remove the iDRAC card before installing the Jumbo PERC card. Steps 1. Remove the connector cap on the I/O connector from the Jumbo PERC card. 2. Lift the blue pull tags to raise the lever up on the Jumbo PERC card. 3. Align the connector, guides, and guide slots on the Jumbo PERC card and the sled. 4. Lower and press the Jumbo PERC card to firmly seat on the system board connector and close the lever on the Jumbo PERC card. Installing and removing sled components 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 68. Removing the Jumbo PERC card
Next steps
1.
Install the Jumbo PERC card
.
Installing the Jumbo PERC card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
section.
3.
Remove the iDRAC card
before installing the Jumbo PERC card.
Steps
1.
Remove the connector cap on the I/O connector from the Jumbo PERC card.
2.
Lift the blue pull tags to raise the lever up on the Jumbo PERC card.
3.
Align the connector, guides, and guide slots on the Jumbo PERC card and the sled.
4.
Lower and press the Jumbo PERC card to firmly seat on the system board connector and close the lever on the Jumbo
PERC card.
Installing and removing sled components
101