Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 104

Removing a MicroSD card, Installing the IDSDM module

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Figure 71. Installing the IDSDM module Next steps 1. Install the MicroSD cards. NOTE: Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. 2. Install the air shroud on the system board. 3. Install the PEM. 4. Follow the procedure listed in the After working inside your sled section. Removing a MicroSD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled section. 3. Remove the PEM. 4. Remove the IDSDM module. Steps 1. Locate the MicroSD card slot on the IDSDM module. 2. Press the card to partially release from the slot. 3. Hold the MicroSD card, and remove it from the slot. NOTE: Temporarily label each MicroSD card with the corresponding slot number after removal. 104 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 71. Installing the IDSDM module
Next steps
1.
Install the MicroSD cards
.
NOTE:
Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal.
2.
Install the air shroud on the system board
.
3.
Install the PEM
.
4.
Follow the procedure listed in the
After working inside your sled
section.
Removing a MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
section.
3.
Remove the PEM
.
4.
Remove the IDSDM module
.
Steps
1.
Locate the MicroSD card slot on the IDSDM module.
2.
Press the card to partially release from the slot.
3.
Hold the MicroSD card, and remove it from the slot.
NOTE:
Temporarily label each MicroSD card with the corresponding slot number after removal.
104
Installing and removing sled components