Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 105

Installing a MicroSD card, Next steps, Prerequisites, Internal SD Card Port, Steps

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Figure 72. Removing a MicroSD card Next steps 1. Install a MicroSD card. Installing a MicroSD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled section. NOTE: To use an MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup. NOTE: If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. Steps 1. Locate the MicroSD card slot on the IDSDM module. Orient the MicroSD card appropriately, and place the contact-pin end of the card into the slot. NOTE: The slot is keyed to ensure correct installation of the card. 2. Press the card into the card slot to lock it into place. Installing and removing sled components 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 72. Removing a MicroSD card
Next steps
1.
Install a MicroSD card
.
Installing a MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
section.
NOTE:
To use an MicroSD card with your system, ensure that the
Internal SD Card Port
is enabled in System Setup.
NOTE:
If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked on
the cards during removal.
Steps
1.
Locate the MicroSD card slot on the IDSDM module. Orient the MicroSD card appropriately, and place the contact-pin end
of the card into the slot.
NOTE:
The slot is keyed to ensure correct installation of the card.
2.
Press the card into the card slot to lock it into place.
Installing and removing sled components
105