Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 119

Steps, Do not lift the system board by holding a memory module, processor, or other components.

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

g. Internal USB memory key (if applicable) h. iDRAC card i. PERC cards j. Jumbo PERC card k. Mezzanine card NOTE: It is required to remove the mezzanine card support brackets for removing the system board from the system. l. Mini Mezzanine cards m. Memory modules and memory module blanks n. Drives o. Backplane p. Control panel q. Drive cage Steps 1. Disconnect all cables from the system board. CAUTION: Do not lift the system board by holding a memory module, processor, or other components. 2. Using the Phillips #2 screwdriver, remove all the screws that secure the system board to the chassis. 3. Holding the edges, lift the system board out of the sled. Figure 88. Removing the system board Next steps 1. Install the system board. Installing and removing sled components 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
g.
Internal USB memory key (if applicable)
h.
iDRAC card
i.
PERC cards
j.
Jumbo PERC card
k.
Mezzanine card
NOTE:
It is required to remove the mezzanine card support brackets for removing the system board from the
system.
l.
Mini Mezzanine cards
m.
Memory modules and memory module blanks
n.
Drives
o.
Backplane
p.
Control panel
q.
Drive cage
Steps
1.
Disconnect all cables from the system board.
CAUTION:
Do not lift the system board by holding a memory module, processor, or other components.
2.
Using the Phillips #2 screwdriver, remove all the screws that secure the system board to the chassis.
3.
Holding the edges, lift the system board out of the sled.
Figure 88. Removing the system board
Next steps
1.
Install the system board
.
Installing and removing sled components
119