Dell PowerEdge MX840c EMC PowerEdge MX840c Installation and Service Manual - Page 108

Removing the M.2 SATA card, Installing the M.2 BOSS module

Get Dell PowerEdge MX840c PDF manuals and user guides View all Dell PowerEdge MX840c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Figure 75. Installing the M.2 BOSS module Next steps 1. Install the air shroud on the system board. 2. Install the PEM. 3. Follow the procedure listed in the After working inside your sled. Removing the M.2 SATA card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your sled. 3. Remove the PEM. 4. Remove the M.2 BOSS module. Steps 1. Using the Phillips #1 screwdriver, remove the screw on the M.2 BOSS module. 2. Pull the SATA card out of the connector and lift the card away from the module. 108 Installing and removing sled components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Figure 75. Installing the M.2 BOSS module
Next steps
1.
Install the air shroud on the system board
.
2.
Install the PEM
.
3.
Follow the procedure listed in the
After working inside your sled
.
Removing the M.2 SATA card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in the
Before working inside your sled
.
3.
Remove the PEM
.
4.
Remove the M.2 BOSS module
.
Steps
1.
Using the Phillips #1 screwdriver, remove the screw on the M.2 BOSS module.
2.
Pull the SATA card out of the connector and lift the card away from the module.
108
Installing and removing sled components