Dell PowerEdge R250 EMC Installation and Service Manual - Page 69

Optional internal USB card, Removing the internal USB key

Get Dell PowerEdge R250 PDF manuals and user guides View all Dell PowerEdge R250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

3. Confirm that the battery is operating properly, by performing the following steps: a. Enter the System Setup, while booting, by pressing F2. b. Enter the correct time and date in the System Setup Time and Date fields. c. Exit the System Setup. d. To test the newly installed battery, remove the system from the enclosure for at least an hour. e. Reinstall the system into the enclosure after an hour. f. Enter the System Setup and if the time and date are still incorrect, see Getting help section. Optional internal USB card NOTE: To locate the internal USB port on the system board, see the System board jumpers and connectors section. Removing the internal USB key Prerequisites CAUTION: To avoid interference with other components in the server, the maximum permissible dimensions of the USB memory key are 15.9 mm width x 57.15 mm length x 7.9 mm height. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. Steps 1. Holding the blue tag, lift the internal USB card to disconnect from the connector on the system board. 2. Remove the USB memory key from the internal USB card. Figure 67. Removing the internal USB card Next steps Replace the internal USB card. Installing and removing system components 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
3.
Confirm that the battery is operating properly, by performing the following steps:
a.
Enter the System Setup, while booting, by pressing F2.
b.
Enter the correct time and date in the System Setup
Time
and
Date
fields.
c.
Exit
the System Setup.
d.
To test the newly installed battery, remove the system from the enclosure for at least an hour.
e.
Reinstall the system into the enclosure after an hour.
f.
Enter the System Setup and if the time and date are still incorrect, see
Getting help
section.
Optional internal USB card
NOTE:
To locate the internal USB port on the system board, see the
System board jumpers and connectors
section.
Removing the internal USB key
Prerequisites
CAUTION:
To avoid interference with other components in the server, the maximum permissible dimensions of
the USB memory key are 15.9 mm width x 57.15 mm length x 7.9 mm height.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Holding the blue tag, lift the internal USB card to disconnect from the connector on the system board.
2.
Remove the USB memory key from the internal USB card.
Figure 67. Removing the internal USB card
Next steps
Replace the internal USB card
.
Installing and removing system components
69